(6) The tension member is fastened together using two bolts, one on each side of the member as shown. Each bolt has a diameter of 12 mm. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is Tallow = 80 MPa and the allowable average normal stress is allow 120 MPa. P 60° P

(6) The tension member is fastened together using two bolts, one on each side of the member as shown. Each bolt has a diameter of 12 mm. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is Tallow = 80 MPa and the allowable average normal stress is allow 120 MPa. P 60° P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P 130 mm 25 mm 25 mm P P 3. Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
answer quickly
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
0.16
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
For the connection shown, determine the shear stress in the 22-mm diameter bolt for an applied load of P= 90 kN. P
Determine the smallest allowable diameter for a circular cross-sectional area of members BD, BE and CE of the truss shown. The working normal stresses are 2000 psi in tension and 1200 psi in compression. (A reduced stress in compression is specified to reduce the danger of buckling.) 12 t 40 kips
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
The lap joint is fastened with four 3/16-in.-diameter rivets. The working stresses are 58 ksi for the rivets in shear and 10 ksi for the plates in bearing. in.
The steel pipe is filled with brass and subjected to a torsion T=34kNm. Determine each torsion value T, and T, taken by steel and brass. S Take the shear modulus for steel G,=80GPA and for brass G,=40GPA. T=34kNm cross-sect lon of A-B 2- steel 1- brass d,=12cm 100cm d;=4cm
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?