OSFu A tension member with an allowable tensile stress of 0.6Fy is connected to the gusset plate using four rivets having a diameter of 34mm. Assume the diameter of the hole is 2mm more than the rivet diameter. It is required to determine the value of b so that the net width along rivets 1-2-3-4 is equal to the net width along 1-2-4. > Determine the value of b Determine the most critical net area The value of T without exceeding the allowable stress. Gusset plate If failure will occur in djagonal s 2 direction add a value 4g 60mm b. 6. 10pmm 400mm 100mm 100mm 12mm 160mm

OSFu A tension member with an allowable tensile stress of 0.6Fy is connected to the gusset plate using four rivets having a diameter of 34mm. Assume the diameter of the hole is 2mm more than the rivet diameter. It is required to determine the value of b so that the net width along rivets 1-2-3-4 is equal to the net width along 1-2-4. > Determine the value of b Determine the most critical net area The value of T without exceeding the allowable stress. Gusset plate If failure will occur in djagonal s 2 direction add a value 4g 60mm b. 6. 10pmm 400mm 100mm 100mm 12mm 160mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.4P

See similar textbooks

Related questions

Q: toonges as aasm 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16…

Q: The 50-mm diameter circular rod creates in the metal sheet a shear stress through section AC and BD.…

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

Q: For the what should be the mini mum tigure show n, dia meter OF the rivets attached as shown TF the…

A: bolted connection - nominal diameter - the actual diameter of the sunk ok the bolt is called the…

Q: In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B.…

A: Given:Diameter of pin at C is 6mmDiameter of pin at B is 10 mmRequired:Largest P applied

Q: P1.020 For the clevis connection shown in the figure, determine the maximum applied load P that can…

A: d = 15 mm = 75 MPa

Q: Q-A 16 mm thick gusset plate is connected to the 12mm thick flange plate of an I-section using…

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

Q: Knowing that P=(4a) kN, Tallow.=60 MPa, Oallow.compressive =140 MPa, a) Find the diameter (d) of the…

A: It is Given that, P = 42 KN ( as it is Mentioned in the Question) Allowable Tensile…

Q: Six rivets are used in the connection shown in the figure. If both P=50kN, what is the minimum…

Q: The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1)…

A: T = 63 N. m

Q: s to be made of steel having an ultimate shearing stress of 400 MPa, determine: (a.)The diameter of…

Q: The two wooden boards are connected by a 0.7 in. diameter bolt. Washers are installed under the head…

A: Given data The diameter of the bolt = 0.7 in The outer diameter of washer (D) = 2.4 in The inner…

Q: Evercise:- A cylindrical rod 100 mm diameter of 12 mm long with is subjected to a 30000 N. Assuming…

A: Given,Initial length of the rod, say L = 100 mmInitial diameter of the rod, say D = 12 mmTensile…

Question

43
OSFu
A tension member with an allowable tensile stress of 0.6Fy is connected to the gusset plate
using four rivets having a diameter of 34mm. Assume the diameter of the hole is 2mm more
than the rivet diameter. It is required to determine the value of b so that the net width along
rivets 1-2-3-4 is equal to the net width along 1-2-4.
> Determine the value of b
> Determine the most critical net area
The value of T without exceeding the allowable stress.
Gusset plate
If failure will occur in djagonal
s 2
direction add a value
4g
C0mm
b.
6.
100mm
400mm
100mm
100mm
12mm
150mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
Select an American Standard Channel shape for the following tensile loads: dead load = 54 kips, live load = 80 kips, and wind load = 75 kips. The connection will be with longitudinal welds. Use an estimated shear lag factor of U = 0.85. (In a practical design, once the member was selected and the connection designed, the value of U would be computed and the member design could be revised if necessary.) The length is 17.5 ft. Use Fy=50 ksi and Fu=65 ksi. a. Use LRFD. b. Use ASD.
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.