A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe P+

For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress = 0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. 300 mm t/2 -P/2 P- -P/2

A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.

Compute the size of fillet weld for a bracket connection with ISMB 300 column as shown in figure. Permissible shear stress in weld = 110 MPa. %3D 425 mm 100 kN 300 Single 12 mm plate 250 mm

Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40

Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten

A bracket connection shown in figure, consists of a joist cutting welded to the flange of a column by shop fillet welds 8 mm on flanges and 6 mm on the web. Determine the safe service load 'W', the bracket can support at a distance of 200 mm from the face of the column if the steel grade is Fe 410. 200 200 8V 150 200 W 8 V 150 N 150 200 250 Partial factor of safety on shop weld = 1.25 Yield strength of steel = 250 MPa. 250 A

Please  kindly give me a,b,c and d answers..help me. Urgent Thank you

For the clevis connection shown, determine the shear stress in the 23-mm-diameter bolt for an applied load of P = 165 kN. O 141 MPa O 211 MPa O 167 MPa O 120 MPa O 199 MPa Clevis

* A 76 mm x 76mm x 6mm angular section is welded to a gusset plate having a thickness of 8mm as shown in the figure. The length L1 equals 125mm and L2 is 65mm. The angular section has a cross sectional area of 929mm2, Fy=248 MPa, Fu=400MPa. Determine the value of tensile force P based on block shear in gusset plate along the weld in kN. Allowable stresses: Allowable tensile stress (gross area) = 0.6Fy Allowable tensile stress (net area) = 0.50Fu Allowable shear stress (net area) = 0.30Fu P gusset plate L₂= 65 mm 25 mm