A double U-shaped butt weld is to connect two plates 200 mm (d) × 20 mm (b), as shown in the given figure. Whatis the stress developed in the weld if it is subjected to a moment of 10000 kN-mm?d=200 mmb=20mm

A double U-shaped butt weld is to connect two plates 200 mm (d) × 20 mm (b), as shown in the given figure. Wha s the stress developed in the weld if it is subjected to a moment of 10000 kN-mm? d=200 mm b=20mm

A double U-shaped butt weld is to connect two plates 200 mm (d) × 20 mm (b), as shown in the given figure. Wha s the stress developed in the weld if it is subjected to a moment of 10000 kN-mm? d=200 mm b=20mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.1P: Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).

See similar textbooks

Similar questions

A double U-shaped butt weld is to connect two plates 200 mm (d) × 20 mm (b), as shown in the given figure. What is the stress developed in the weld if it is subjected to a moment of 10000 kN-mm? d=200 mm festbook b=20mm
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
7
4.) A 150 x 90 x 12 angular section is welded to a gusset plate as shown in the figure. The angle is A36 steel with FY=248 MPa. The weld is E 80 electrode with Fu = 550 MPa. The allowable tensile stress for the angle is 0.6Fy and the allowable shear stress for the weld is 0.3Fu. The Area of the angular section is 2751 sq.mm. with y=51mm. CS 56 Which of the following most nearly gives the design force P? a.) 400,365.9 N b.) 409,348.8 N c.) 412,793.5 N d.) 420,366.6 N 5.) A W350 x 90 steel is used as a simply supported beam 8m long. The beam carries three equal concentrated loads at every quarter points. It also carries a uniform dead load o 5 kn/m (including its own weight) and a uniform live load of 7.20 kn/m. Properties of W 350 x 90 steel: bf = 250 mm The allowable bending stress is 0.66Fy. The allowable shear stress is 0.40Fy. The allowable deflection is L/360. Use Fx=248 Mpa and E=200 Gpa. tf = 16.40 mm V d = 350 mm Determine the maximum value of each concentrated load based on…
A rectangular plate of dimensions 100 mm x 250 mm is formed by welding two triangular plates (see the figure). The plate is subjected to a compressive stress of 2.5 MPa in the long direction and a tensile stress of 12.0 MPa in the short direction. 12.0 MPa Weld 250 mm- 100 mm 2.5 MPa (a) Determine the normal stress o, acting perpendicular to the line of the weld. (Assume that the normal stress a, is positive when it acts in tension against the weld.) Round to one decimal place. MPa (b) Determine the shear stress T acting parallel to the weld. (Assume that the shear stress T, is positive when it acts counterclockwise against the weld.) Round to one decimal place. T = MPa
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1) Figure ▾ art A Tavg for Part A for Part 12 mm Value T= 60 N-m 50 mm- Determine the average shear stress in the weld along section a-a if the torque applied to the shafts is T = 63 N-m. Note: The critical section where the weld fails is along section a-s. Express your answer to three significant figures and include the appropriate units. Units 12 mm 1 12 mm 12 mm a do for Part 1 of 1 redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A
The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1) Figure Part A 12 mm Tavg 1.229 -50 mm на фра рабо T=60 N·m MPa Determine the average shear stress in the weld along section a-a if the torque applied to the shafts is T = 63 N. m. Note: The critical section where the weld fails is along section a-a. Express your answer to three significant figures and include the appropriate units. Submit Previous Answers Request Answer 12 mm ? 12 mm a 12 mm * Incorrect; Try Again; 24 attempts remaining 1 of 1
S Example 8.7 An ISA 200x100x10 angle LO 3 is welded to a steel plate by means of fillet welds as shown in Fig. 8.17. The angle is subjected to a static force of 150 kN and the permissible shear stress for the weld is 70 N/mm². Determine the lengths of weld at the top and bottom. 1₁ 150 kN TAILL Y2 200 12 - IG 100- 12 71.8 150 KN -10
A plate is connected to the column using fillet welds as shown. The size of weld is 8 mm. Determine the following: a. Shear stress due to load alone b. Shear stress due to moment c. Maximum shear stress.
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively.
Explain it