The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determinethe smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter dof the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa andallowable shear stress is allow=125 MPa.BA140 KN- dzd₂20 mm10 mm

Given : Load supported = 140 kN Allowable bearing stress = 350 MPa Allowable shear stress = 125 MPa…

The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow = 125 MPa. R. d₁ A 140 kN 20 mm 10 mm

The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow = 125 MPa. R. d₁ A 140 kN 20 mm 10 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Related questions

Q: 2. A finite element analysis of a bearing housing indicates that at a point p, the material is…

A: Principle stresses are the those stresses that are to the normal with zero plane. The value of…

Q: e average normal stress

Q: A 116.79 kips (B 172.79 kips 92.79 kips A 119.38 kips B 40 kips 1.5" V 40 kips C From the figure,…

A: dia of rod AB=2''allowable stress in rod AB=55ksi

Q: The lower end of the three bars in the figure are at the same level before the rigid homogeneous 18…

Q: Before the 400 kN load is applied, the rigid platform rests on two steel bara, each of cross…

Q: P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam…

A: b = 130 mm h = 200 mm P = 25 KN w = 30 KN/m

Q: P = 9 kip 2 in. 1 in. 1.5 ft The aluminum post shown in the figure is reinforced with a brass core.…

Q: The cross section of the machine part is a square, 5 mm on a side. If the maximum stress at section…

A: Given Area of square cross section A=52=25mm2=25×10-6m2 Maximum allowable stress at section m-n…

Q: Problem 5-82 The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN…

A: Given:- The Am1004-T61 magnesium tube is bonded with an A-36 steel rod The magnitude of the torque…

Q: Problem 4. The block is subjected to a compressive force of 2kN. Base= 60mm, Height = 170mm. 1.…

Q: A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its…

A: A steel pipe is subjected to the 16-kN load shown below.Outer diameter = 140 mmThickness = 7 mmYield…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that dị…

Q: The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870…

Q: Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a…

A: I am solving only three sub parts as per Bartleby guidelines.

Q: 0.2: The rigid platform has negligible mass and rests on two steel bars, each 250.00 mm long. The…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine
the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d
of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and
allowable shear stress is allow=125 MPa.
B
A
140 KN
- dz
d₂
20 mm
10 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Estimate the transverse tensile strength of the concrete in Problem 12.6.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
How does a tensile stress differ from a compressive stress?
For silver at a tensile stress of 7 MPa and a temperature of 839C , there are two equally contributing creep mechanisms. What are they?
In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.