Two identical plates are connected by two 18-mm diameter rivets as shown.Consider the following dimensions:B = 200 mmt = 22 mmx = 16 mmThe allowable stresses of the plate are the following:Normal stress = 18 MPaBearing stress = 4 MPaShearing stress = 5 MPaDetermine the maximum force P:A. Considering the normal stress: P =B. Considering the bearing stress: P =C. Considering the shearing stress: P =Express your answers in three decimal places.KNkNKNO CHEGG.CO ISLSTRINGURVE VARSITY TUTUPINSTUTORIAL TE SUCH, BO CHEGG COURSEHERO, SKOOLI TUTORET TUTURME VARSITY TUTORS, WZANT. ETC.DISTRIBUTION TO ANY PARTY IS PROHIBITED,INSTITUTIONAL EXAM NOT EUPLOADING ON ANY TUTORIAL SITE SUCHLEDO CHEGG, COURSEHERO, SKOTTOREYZ TUTORM VARSITY TUTORS, W ZAWI, ETC.P4DISTRIBUTION TO ANY PARTY IS PROHIBITED.NOTPSN INSTITUTIONAL EXEM NOT FOR REUPLNG ON ANY TUTORIAL SITE SUC30 CHEGG, COURSEHERO, SKOOL TUTO+STORM VARSITY TUTORS, WDISTRIBUTION TO ANY RTY IS PROHIBITED.THERO, SKOOL TUTOREY TUTORME VANYERTY IS FROIAM, NXT FOR REXPLOADINGXON ANY 1DIST BUTIONZAC.B

Answered: Image /qna-images/answer/c4b82513-6009-4469-aa6c-81d50e9388b7.jpg

Two identical plates are connected by two 18-mm diameter rivets as shown. Consider the following dimensions: B = 200 mm t = 22 mm x = 16 mm The allowable stresses of the plate are the following: Normal stress = 18 MPa Bearing stress 4 MPa Shearing stress = 5 MPa Determine the maximum force P A. Considering the normal stress: P = B. Considering the bearing stress: P = C. Considering the shearing stress: P = Express your answers in three decimal places. KN KN KN P. UTORIAL ESCH E VERIUTY TUTORE ZANT MNG LEGO COURSEO SKO TUTORE DISTRIBUTION TO ANY TO ANY PARTY IS PROHIBITED INSTITUTIONAL NOT UPLOADING ON TUTORIAL SITES O CHEGO, COURSEHRO STOREY TUTOR VARSITY TUTORS, W DIST BUTION TO ANY PARTY IS PROHIBITED INSTITUTIONAL EM NOT FOR REUP ON Y TUTORIAL SITE SU CHEGG, COURSEHERO, SKOOL TUTORTOR VARSITY TUTORS, W DISTRIBUTION TO ANY RTY IS PROHIBITED. TORE TUTORM SKOCK X X X DE ZA ROL HANY EIG TP B

Two identical plates are connected by two 18-mm diameter rivets as shown. Consider the following dimensions: B = 200 mm t = 22 mm x = 16 mm The allowable stresses of the plate are the following: Normal stress = 18 MPa Bearing stress 4 MPa Shearing stress = 5 MPa Determine the maximum force P A. Considering the normal stress: P = B. Considering the bearing stress: P = C. Considering the shearing stress: P = Express your answers in three decimal places. KN KN KN P. UTORIAL ESCH E VERIUTY TUTORE ZANT MNG LEGO COURSEO SKO TUTORE DISTRIBUTION TO ANY TO ANY PARTY IS PROHIBITED INSTITUTIONAL NOT UPLOADING ON TUTORIAL SITES O CHEGO, COURSEHRO STOREY TUTOR VARSITY TUTORS, W DIST BUTION TO ANY PARTY IS PROHIBITED INSTITUTIONAL EM NOT FOR REUP ON Y TUTORIAL SITE SU CHEGG, COURSEHERO, SKOOL TUTORTOR VARSITY TUTORS, W DISTRIBUTION TO ANY RTY IS PROHIBITED. TORE TUTORM SKOCK X X X DE ZA ROL HANY EIG TP B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm 啡 F mm. 50 mm 340 mm
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm mm. 50 mm 340 mm
A solid brass shaft is loaded as shown below by two torques TB segments are LAB = 750 mm and LBC = 600 mm. = TB Тс A dAB B dBC C LAB LBC 1100 Nm and TC: = 400 Nm. The lengths of the two For brass, G = 41 GPa. Neglect the effect of any stress concentrations. Determine the smallest diameters dдB and dBC for which an allowable shear stress of 60 MPa is not exceeded. Express each diameter as an integer in units of mm.
7
I'll upvote if complete and correct. Thank you
2. Two rods connected as shown carry a vertical load of 20 kN. Rod AB is a steel rod with E = 2 X10 MPa while rod BC is made up of aluminum whose E = 7x10¹MPa. The rods are rigidly pinned at A and C and have cross-sectional areas equal to 400 mm². If a is changed from 30° to 45°, compute: (a) stresses in each rod. Specify if tensile or compressive stress (b) deformation of each rod. Specify if elongation or shortening. B P=20 KN L=3m α=30° 70=30° L=2m
please recheck your final answer.
Please give me both answers.... Help me Urgent... Thank you
A plate is connected to another plate via 20 mm diameter rivets. It carries a load of P=155 kN at a distance of (155+67) mm from the rivet group's centroid. Assume a = 131 mm. (Hint: There is no NSCP involved; therefore, load factors are omitted.) Identify the following: 1. Shear stress (kPa) on each rivet due to force alone?2. Shear stress (kPa) on each rivet due to torsion alone?3. Shear stress (kPa) on the highly stressed rivet
observe the given values carefully and give me right solution with clear calculations. Don't copy from other experts solution
The post shown, whose cross-sectional area is 100 x 150 mm2, rests at the middle of a circular solid steel plate. The steel plate is placed above a hollow cylinder. Both the steel plate and the cylinder have diameter of 300 mm and a thickness of 20 mm. Solve for the following: a. punching shear stress in the steel plate b. punching shear stress in the hollow cylinder c. bearing stress in the steel plate due to the post d. bearing stress in the cylinder due to the steel plate
Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of elasticity E=200 GPa, cross sectional area A=500 mm2. Determine the ww normal stress in each bar due to load P. a a=280mm b=70mm C=1177mm L=1075mm P=775mm L E B D F