A wooden beam is fabricated by bolting together three members. The cross-sectional dimensions are shown. The 7-mm-diameter bolts are spaced at intervals of s- 100 mm along the x axis of the beam. If the internal shear force in the beam is V-11 kN, determine the shear stress r in each bolt. Assume by - 46 mm, b₂-39 mm, dy-62 mm, d₂-290 mm.

A wooden beam is fabricated by bolting together three members. The cross-sectional dimensions are shown. The 7-mm-diameter bolts are spaced at intervals of s- 100 mm along the x axis of the beam. If the internal shear force in the beam is V-11 kN, determine the shear stress r in each bolt. Assume by - 46 mm, b₂-39 mm, dy-62 mm, d₂-290 mm.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: A 20-mm-thick plate is bolted to the flange of a T-beam to form a -200 mm 20 mm built-up beam. If…

A: Calculate the moment of inertia of I section…

Q: Two plates are joined by four bolts of d=20-mm diameter, as shown in the figure. The shearing stress…

A: We have to determine the value of maximum load P as the shearing stress is limited to 70 MPa,…

Q: - A joint is made by gluing two plywood gussets of thickness to wood boards. The tensile working…

A: The tensile working stresses for the plywood is 1200 psi.The tensile working stress for the wood…

Q: Set P₁ = 1.6 kN and P₂ = 1.2 kN. (EFigure 1) Figure 30° 3 m D P 30/ 3m P₂ ▼ Determine the force in…

Q: 02. The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find…

A: Apply deflection condition i.e PL/AE. Where P is load

Q: SITUATION. A steel plate ABCD of thickness t Smm is subjected to uniform stresses E2000Pa, y 13…

Q: Lesson 1: Simple Stress #1. The assembly shown below is pinned at A & Cand A&C are subjected to a…

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear…

A: Given data in question Load 750 kN Diameter 32 mm To find out Permenant strain

Q: A steel beam is bolted to a steel girder by a connection similar to that in the figure shown below.…

A: It is the objective of each steel plan to guarantee that the parts are accurately associated with…

Q: own below is 500 mm². 4. 3 m 3 m 3 m Determine the load P that will not (ceed a stress of 100 MPa in…

A: First find the reactions at the supports And then find the internal force in each member using…

Q: A The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find…

Q: Two plates are joined by 4 rivets 25mm diameter as shown in the figure. Assume diameter of rivet…

A: given data: Diameter of rivet (d) = 25 mm diameter of rivet hole (dhole) = 28 mm Allowable stresses:…

Question

A wooden beam is fabricated by bolting together three members. The cross-sectional dimensions are shown. The 7-mm-diameter
bolts are spaced at intervals of s 100 mm along the x axis of the beam. If the internal shear force in the beam is V-11 kN, determine
the shear stress r in each bolt. Assume by - 46 mm, b₂-39 mm, dj-62 mm, d₂ - 290 mm.
M
Answer: r = i
MPa.
di
T

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Estimate the transverse tensile strength of the concrete in Problem 12.6.
Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Use an elastic analysis and determine the maximum load per inch of weld.
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
How does a tensile stress differ from a compressive stress?