A 20-mm-thick plate is bolted to the flange of a T-beam to form a -200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm

A 20-mm-thick plate is bolted to the flange of a T-beam to form a -200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If you don't know the solution please leave it but don't copy from other websites solution
Determine the resultant load on the most stressed bolt in the eccentrically loaded connections shown, using the elastic method.
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1) Figure ▾ art A Tavg for Part A for Part 12 mm Value T= 60 N-m 50 mm- Determine the average shear stress in the weld along section a-a if the torque applied to the shafts is T = 63 N-m. Note: The critical section where the weld fails is along section a-s. Express your answer to three significant figures and include the appropriate units. Units 12 mm 1 12 mm 12 mm a do for Part 1 of 1 redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A
Steel design
3. Please include FBD & make the solutions understandable
Please show FBD and complete solution.
The double T-beam is fabricated by welding the three plates together as shown. Part A Determine the shear stress in the weld necessary to support a shear force of V=78 kN�=78 kN.
Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 80 MPa O 71 MPa O 74 MPa oooo O 86 MPa O 1. Which of the following nearly gives the shearing stress of the most stress bolt? Use 20 mm diameter bolt. x1 O O O x2
a.)What torque can be applied without exceeding the shearing stress of 60 MPa in the steel bolts and 40 MPa in the aluminum bolts? (in kNm) b.)Using the Torque calculated above, what is the maximum shearing stress in the steel bolts? (in MPa) c.)Using the Torque calculated above, what is the maximum shearing stress in the aluminum bolts? (in MPa)
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. Please show your complete handwritten solution. Thank you
Shear strength value τ = 200 MPa The contents associated with bolts are given. P = 70 kN required for the safe transfer of the load of value Determine the minimum bolt diameter