QUESTION 2) The state of strain at point A onthe bracket is measured using the strain rosetteshown in Figure. Due to the loadings, the readingsfrom the gauges give ɛa-150x10, £v=200x106 andEc=100x106 Determine the in-plane principal\30°stresses at the point and the directions in whichthey act.150°a,xTake the modulus of elasticity as E= 80 GPa andPoisson ratio as v = 0.3.

Answered: Image /qna-images/answer/6b11ea29-75d0-4f3b-995c-68f5c1053886.jpg

QUESTION 2) The state of strain at point A on the bracket is measured using the strain rosette shown in Figure. Due to the loadings, the readings from the gauges give ɛa=150x10", e-200x10 and Ec=100x106 Determine the in-plane principal stresses at the point and the directions in which \30° they act. 150° a,x Take the modulus of elasticity as E= 80 GPa and Poisson ratio as v= 0.3.

QUESTION 2) The state of strain at point A on the bracket is measured using the strain rosette shown in Figure. Due to the loadings, the readings from the gauges give ɛa=150x10", e-200x10 and Ec=100x106 Determine the in-plane principal stresses at the point and the directions in which \30° they act. 150° a,x Take the modulus of elasticity as E= 80 GPa and Poisson ratio as v= 0.3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 60 MPa, σy=σy= 80 MPa, and τxy=τx⁢y= 42 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 72 GPa and v = 0.29 for the machine component.
Three strain gauges are attached on the surface of the plane frame which is shown in Figure. The angle between each strain gauges are θº=69º. Reading from these gauges are: εa= 1100 μ, εb =305 μ and εc = -240 μCalculate:(a) The principal strains(b) The maximum shear strain
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 880 psi in size. (a) Determine the stresses ox, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). y Answer: (a) Ox = psi Oy = psi Txy = psi (b) Op1 = psi Op2 = psi Tmax in-plane psi
Question 1: The piece of plastic is originally rectangular. Given LCD and LAD are 400 and 300 mm, respectively. If the plastic distorts as shown by the dashed lines, a) Determine the average normal strain that occurs along CD. b) Determine the average normal strain that occurs along AD. c) Determine the shear strain Yxy at corner C. 2 mm LCD 2 mm D LAD mm B 12 mm 3 mm mm
bb new 10
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 480 psi in size. (a) Determine the stresses o,, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). y
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 320 psi in size. (a) Determine the stresses Ox, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). X D C y b
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 740 psi in size. (a) Determine the stresses o,, Oy, and the magnitude of Tyy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g. see Figure 12.15 or Figure 12.16). y
Answer in two decimal places please
3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa 4. In question 3, assume that the bar is free to elongate or shorten, calculate the change in the length of the bar if the temperature drops from 20°C to -20°C.
1.4
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx= 100 MPa, σy= 65 MPa, and τxy= 70 MPa, acting in the directions shown in the figure. At this point, determine the strain components εx, εy, εz, and γxy. Assume that E = 71 GPa and v = 0.28 for the machine component.