Question 1: The piece of plastic is originally rectangular. Given LCD and LAD are 400 and 300 mm, respectively. If the plastic distorts as shown by the dashed lines, a) Determine the average normal strain that occurs along CD. b) Determine the average normal strain that occurs along AD. c) Determine the shear strain yxy at corner C. 2 mm LCD 2 mm D LAD A mm 4 mm 72 mm 3 mm

Question 1: The piece of plastic is originally rectangular. Given LCD and LAD are 400 and 300 mm, respectively. If the plastic distorts as shown by the dashed lines, a) Determine the average normal strain that occurs along CD. b) Determine the average normal strain that occurs along AD. c) Determine the shear strain yxy at corner C. 2 mm LCD 2 mm D LAD A mm 4 mm 72 mm 3 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.2 in.2 and an elastic modulus of 1820 ksi. Bar (2) has a cross-sectional area of 1.185 in.2 and an elastic modulus of 3590 ksi. Assume L1=21 in., L2=48 in., Q=7.6 kips, P=2.6 kips, and R=12.8 kips. Determine the horizontal deflection of end C relative to end A.
Q) The rectangular plate shown in the figure below with dimensions h=20 mm and b=50 mm changes shape symmetrically with respect to the x-axis after in-plane loading. At the same time, point B is displaced in the plane Ab 0.12 mm, Ah = 0.03 mm. After deformation; a) What is the strain in the x-axis direction? b) Find Ecb c) What is the angle of shear between the DG and GH edges? C H. H' B' 2h Ah Ab -
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 220-mm-gage length. Using E = 180 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm.
The force applied at the handle of the rigid lever as shown in figure 1 causes the lever to rotate clockwise about the pin B through an angle of 2 degree. Determine the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. If the wires,in figure 1, AB, CG and FD are made of Aluminum, Copper and steel with a diameter of 3mm find the force stress in each of the wire and also the force applied.
The ability of the material to absorb energy without creating a permanent distortion is called. O a. Hardness O b. Tuohgness O c. Resilience O d. Rapture
The major and minor principal strains in a 2D stressed element are 70μ and -25µ respectively. If the normal strain at a plane is given as 15µ, then what will be the normal strain on a plane perpendicular to it? A B d C D 40μ 30μ 25μ 20μ
The state of stress at a critical section is shown in Fig. Determine the state of stress on the element inclined at an angle of 30° clockwise from the x-axis. Represent these stresses on the element. 50 MPa - 100 MPa 25 MPa
A bar having a cross-sectional area of 700 mm² is subjected to axial loads at the positions indicated. The value of stress in the segment BC is 21kN 63KN 35kN + 49kN A В (а) 40 MPа (b) 50 MPа (c) 70 MPa (d) 120 MPa
Answer in two decimal places please
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A? Determine the shear strain γnt at point A? In micro rad What is the normal strain in the x-direction? What is the normal strain in the y-direction? What is the normal strain in the n-direction? Answer in clear way please
Show the step by step solution for problem 2-12
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 280-mm-gage length. Using E = 140 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 60 mm, b = 110 mm, and c = 70 mm.