A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The dimensions of the block are as follows: L_x=100 mm,L_y=30 mm,L_z=40 mm. Determine the change in length along the y-axis. Use E = 200 GPa and v 0.3. Note that e_0=-o/E(1+2v). A -0.03 mm -0.015 mm -0.009 mm -0.012 mm

A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The dimensions of the block are as follows: L_x=100 mm,L_y=30 mm,L_z=40 mm. Determine the change in length along the y-axis. Use E = 200 GPa and v 0.3. Note that e_0=-o/E(1+2v). A -0.03 mm -0.015 mm -0.009 mm -0.012 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The assembly shown in figure below consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is touch to its support. A 0.75 m Steel A = 250 mm E = 200 GPa *i* O 1.5 m Aluminum L = 2m A = 300 mm' E = 70 GPa B D
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
Steel bar of cross-section 550mm2 is acted upon by the forces shown in figure. For steel, E = 200GPa. Compute the stress in BC Compute deformation of AB Compute the total elongation of the assembly.
The section of a thick beam has the dimensions shown in the figure below. Calculate the section properties lz, ly and Izy (Izy = product of inertia) referred to horizontal and vertical axes through the centroid of the section. Refer to Section 6 in your notes for properties of planed sections. Also determine the direct stress at the point A due to a bending moment My = 55 Nm. (Hint: use Page 7-9 in your notes) Ay A 5 mm 20 mm G 5 mm 5 mm 10 mm
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
The rigid bar is supported by a smooth pin and two rods as shown. Neglect the weight of the rigid bar. The assembly is initially stress-free. Determine the stress in each rod if the temperature increases by 25°C after a load W = 100 kN is applied. The steel rod has an area of 320 mm² with a = 11.7 um/ ( m°C ) and E = 200 GPa. For the bronze rod, it has an area of 1380 mm? with a = 18.9 µm/ ( m°C ) and E = 83 GPa. Bronze | 3 m Steel | 1.5 m 1.0 m - - 2.5 m +1.5 m→
A flat steel bar, 30 mm wide by 2 mm thick and 1.3 m long, is bent by couples applied at the ends so that the midpoint deflection is 27 mm. Compute the maximum stress in the bar. Use E = 220 GPa. Answer must be in MPa.
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
3. The rigid bar ABC is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the steel rod if the temperature of the both rods is decreased by 30°C. Neglect the weight of bar ABC. Steel L=0.9 m A 300 mm E= 200 x 10 N/m' a= 11.7 um/(m C) Aluminum L=1.2 m A = 1200 mm E = 70 x 10 N/m a= 23 pum/(m "C) Answer: Ost B 0.6 m 1.2 m
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa