Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure ). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm D = 40 mm. Y-face D 50 X-face 30MN m-2 30 50 MN m-

Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure ). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm D = 40 mm. Y-face D 50 X-face 30MN m-2 30 50 MN m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
A solid brass shaft is loaded as shown below by two torques TB segments are LAB = 750 mm and LBC = 600 mm. = TB Тс A dAB B dBC C LAB LBC 1100 Nm and TC: = 400 Nm. The lengths of the two For brass, G = 41 GPa. Neglect the effect of any stress concentrations. Determine the smallest diameters dдB and dBC for which an allowable shear stress of 60 MPa is not exceeded. Express each diameter as an integer in units of mm.
help me asap pls :((
7.A cast-iron machine part is acted upon by the 3kN.m couple shown. Knowing that E=165GPA and neglecting the effect of fillets. i) Determine the maximum tensile and compressive stress in the casting ii) Determine the radius of curvature of the casting. 90 mm 20 mm 40 mm 30 mm M = 3 kN m
I'll upvote if complete and correct. Thank you
Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 - F 8 mm 8 mm ↓ 12 mm P
The rectangular bar shown is connected to a support bracket with a 16 mm diameter pin. The width of the rectangular bar is 60 mm and its thickness is 25 mm. The bearing stress in the bar cannot exceed 200 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support bracket
Consider the singly reinforced beam section given below (left figure). The stress block parameters for the cross-section from IS: 456: 2000 are also given below (right figure). The moment of resistance for the given section by the limit state method is kN-m. 300 mm M25 4-120 Fe415 200 mm 0.42x 0.36 um = 0.48d for Fe415
How do I solve this using Mohr’s Circle
idity modulus doengro 17. A 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 90 MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is as aeqml 19WOL to da odt ons aasmos m noienet ni mioj по djiw YIVO P/24 F 12mm ↑ P/2 00 8mm 8mm
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm 啡 F mm. 50 mm 340 mm
Solve asap