The system under the effect of torsion; a- Draw the torsional moment diagram. b- Determine the torsion angle CA (rotation angle) that will occur at point C. c- Determine the load shear stress. (G=80 000 MPa M1=5000Nm  M2=4000Nm  D1=120mm   D2=90  D3=80  D4=60

Q: 2. A finite element analysis of a bearing housing indicates that at a point p, the material is…

A: Principle stresses are the those stresses that are to the normal with zero plane. The value of…

Q: Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque)…

A:

Q: 4. Compute for the maximum value of force P that can be applied if the allowable bending stress is…

A:

Q: the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter…

A:

Q: Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of…

A: Draw the free body diagram. Equilibrium of vertical forces,…

Q: The strain in the x direction at point A on the A-36 structural-steel beam(in figure attacched) is…

A: Neutral axis: YNA=122=6 inMoment of inertia:I=6×12312=864 in4   stress: stressσ=E×strain in x…

Q: --29. The rectangular plate is deformed into the shape shown by the dashed li verage normal strain…

A:

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD2- if Beam Weighs is not know then finding of…

Q: 2. The lengths LAB = LBC = 20o mm and LCD = 240 mm. The diameter of parts AB and CD of the bar is 25…

A:

Q: Q4/ Determine the moment M that must be applied to the beam in order to create a maximum stress of…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine loadP that can…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A:

Q: the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to…

A:

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the…

A:

Q: The two bars are made of polystyrene, which has the stress-strain diagram shown. If the…

A: Given : Cross sectional area of bar AB is = 975 mm2 Cross Sectional area of bar BC = 2600 mm2…

Q: Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in…

A:

Q: 8-47. Determine the state of stress at point A, and show the results on a differential volume…

A: Given : Determine the state of stress at point A and show the results on a differential volume…

Q: The shaft is made from a solid steel section AB and a tubular portion made of steel and having a…

A:

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A:

Q: D. 150 mm E B -150 mm-|-2 mm (a) Al-76 mm--76 mm-p 75 mm The plate shown in the figure is a fixed…

A:

Q: 200mm P Strain gauge F 100m mmm 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used…

A:

Q: Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole…

A: bending stress=MmaxIyt I= 100× 106 mm4 Yt= 200mm Mmax=6P =6×19=114 kNm( hogging) Hence will cause…

Q: The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pin and…

A: GIVEN- d=1.5mm E=200GPA The F.B.D diagram is shown below

Q: QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum…

A: Soln⇒ * Neutral axis orientation* A1 = 10×40 ⇒400 mm2  , X1=402 ⇒ 20mm, y1= 5 mm   A2 = 50×10 ⇒500…

Q: 30 mm A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and…

A: Given Data Find the bending stress at point A, B and C.

Q: The rigid bar ABC shown in the figure is hinged at A and supported by a steel rod at B. Determine…

A: Force on steel rod = Ft Stress in steel rod -  σst = FtA here,  A = Area of steel rod. ⇒30 =…

Q: The frame supports the distributed load shown. Determine the state of stress acting at point E. Show…

A: Draw the free body diagram.

Q: . The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not now the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD 2- if Beam Weighs is not know then finding of…

Q: The rectangular plate undergoes a deformation shown by the dashed lines. Determine the shear strain…

A: Since the position of x and y axes do not change after deformation , the shear strain at point A  is…

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.