The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut, determine the stress in each wire when a 1200 N load P is applied at D. What is the corresponding deflection of point D?

Q: The armor shown supports a pedestrian bridge between two buildings that it exercises vertical…

A: To determine the axial force in member BC of the given truss.   In the method of section, a…

Q: E-11 The aluminium alloy wing section shown is subjected to a pure torque of 100kNm over its 10m…

A: The given data is shown below: Torque=100 kN-mLength=10mG=30 GPa

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A: Given : Diameter of wire CD = 1/8 inches Diameter of the pin at B = 1/8 inch Determine the tensile…

Q: If the beam is subjeded to a shear Compute the maximum shor stress b- Compute the shear stress 40 mm…

A: I = 200310312-170250312I = 275.16×106 mm4V = 40 kNQ = VAy¯Ib, whereV = Shear ForceA = Area above the…

Q: The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid…

A: Given Load PSpan 12 ftTo find out Normal stress in CG

Q: Which of the following is NOT TRUE as an assumption in the elastic analysis of circular members…

A:

Q: the deflection at B by integnition method A 2 1.5 B TELE C loku D

A:

Q: 9-14. The state of stress at a point is shown on the element. Determine (a) the principal stress and…

A:

Q: Problem # 3: The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a…

A:

Q: The center post B of the assembly has an original length of 124.4mm whereas posts A and C have a…

A: To determine the average normal stress in the posts.   Given, Length of posts A and C (L1) = 125 mm…

Q: A steel pipe of 300-mm outer diameter is fabricated from an 8-mm-thick plate by weldingalong a helix…

A: Step 1:Step 2:

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow =60 MPa.…

A:

Q: A В C D a E F G Н F

A: using method of sections sign convention tensile =+ compressive = -

Q: : A tripe-U shear mount used four 10 mm x 60 mm x 100 mm hard rubber blocks. Upon loading, the upper…

A:

Q: EX. A steel rod 2 m hong has end fram a support structureand fa end a cross- sectional fa3 cm?. The…

A:

Q: 4 in 7/8 in 7/8 in 2. The lap joint shown in the figure, is fastened by four 25mm.-diameter rivets.…

A:

Q: V. Knowing that the rectangular section beam shown is made of steel for which the allowable stress…

A:

Q: 2. The engine of the helicopter is delivering 600 hp to the rotor shaft AB when the blade is…

A:

Q: The pin-connected rigid rods AB and BC are inclined at 0 the force P is applied, 0 becomes 32°.…

A:

Q: The curved member is made from a material having allowable bending stress of sallow = 100 MPa.…

A:

Q: H.W.: A horizontal rigid bar AB is hinged at A and subjected to 80 kN load and 120 kN.m moment at C…

A:

Q: Consider the beam as shown in the figure. The maximum shear is found to be 1.5P Ibs. The moment of…

A:

Q: 450 mm 250 mm B DV 300 mm 300 mm 300 mm

A:

Q: A For the beam loaded as shown in figure, the location of point of contra flexure from the left end…

A:

Q: The lap joint is fastened with four 3/4-in.-diameter rivets. The working stresses are 14 ksi for the…

A: Given Shear stressτ=14ksi=14000psiBearing stress σb=18ksi=18000psiDiameter,d=34inThickness,t=78in To…

Q: A steel shaft is loaded as shown. Knowing that T₁ = 600 N.m, T₂ = 2600 Nm, L=250 mm, -40 mm, D=45…

A: Given data in question  Torque 600 & 2600 Nm Length 250 mm Diameter 40 & 45 mm Modulus of…

Q: The lap joint is connected by three 40-mm-diameter rivets. Assuming that the axial load P= 70 kN is…

A:

Q: Q12 (Simple stress and strain) Item 3 of 3 A bar AB (A = 500 mm?) is hinged at A and is supported by…

A: Given Data:A=500mm2W=90kND=20mmE=200Gpa

Q: = The solid steel shaft carries the torques T₁ 750 N-m and T₂-1200 N-m. Using L₁ L₂ 2.5 m and G-83…

A:

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze (E -…

A: Given data: As=1.228 in2Es=30000 ksiAb=0.637 in2Eb=15000 ksi

Q: -4 m- B 60 E 60 D 4 m- 4 m- 'P

A: Given section: FBD:

Q: 600 400 600 800 Gl P2 P3 E F Tha at y pnywty A - 100 mm" E- 200 GPa A- 150 mm E- 200 GPa A130 mm E-…

A:

Q: *8-36 The frame supports a centrally applied distributed load of 1.8 kip/ft. Determine the state of…

A:

Q: QUESTION 1 The assembly consists of two rods and a horizontal bar BC. Each of the rod AB and CD is…

A: Calculate the deflection at E?

Q: Solve the problem using Moment -Area Method Problem II. The midpoint B of the steel cantilever beam…

A: This question is related to the Strength of Material.

Q: An unsymmetric moment of M = 5 kN.m is applied on the cross-section of an aluminum beam. Find the…

A:

Q: D 200 mm 300 mm -400 mm- A C When force P is applied to the rigid arm ABC, point B displaces…

A:

Q: A load of P = 4261 N is acting on member AC. The length of AC is d = 320 mm. The cross-sectional…

A:

Q: 125. A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18…

A:

Q: The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and…

A:

Q: is three times larger than in steel shaft. Q1) For the section shown aside, if the bending stress at…

A:

Q: 1. The beam ABCD with a rectangular cross section carries the loading shown in the figure. Determine…

A: a. Determine the magnitude of maximum bending stress.  b. Location of the maximum bending stress.