The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa. Neglect torsional effect. T 400 mm BO The maximum safe value of P is 30° P 480 mm kN. (Round off to one decimal place)

The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa. Neglect torsional effect. T 400 mm BO The maximum safe value of P is 30° P 480 mm kN. (Round off to one decimal place)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 35 kN. Assume that a = 240 mm,…

A: Given Data Determine the average shear stress in the pin-B.

Q: A 120-mm-wide steel bar with a butt-welded joint, as shown. SHEAR STRESS NORMAL STRESS 95 MPa SET…

A: Determine the minimum thickness of the steel bar.

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

Q: (6) The tension member is fastened together using two bolts, one on each side of the member as…

Q: A 20-mm-diameter rivet joins the plates that are each 110 mm wide. The allowable stresses are 120…

Q: P1.020 For the clevis connection shown in the figure, determine the maximum applied load P that can…

A: d = 15 mm = 75 MPa

Q: A force P = 70 kN is applied at the plate-bolt connection shown. Determine the required diameter in…

Q: For the shaft loaded as shown, which point(s) at the section shown experiences the maximum shear…

A: Let's draw the FBD for first figure At the L shaft observe the stresses and their directions…

Q: Problem 2: A bar is made from bonded pieces of steel (E = 29x10 psi) and brass (E = 15x10 psi).…

A: Given : Es = 29 X 106 psi Eb = 15 X 106 Determine the max. stress in the steel and brass when a…

Q: The hanger is supported using a rectangular pin. Determine the magnitude of the allowable suspended…

Q: 2. A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm…

Q: 0.75 in. A 1 in. 20° 1.5 in. -→-1 in.-- 4 in. 5 lb

A: Consider the free body diagram shown below. From the figure, tanθ=1+0.754θ=23.6294° All the joints…

Q: 3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear…

Q: The pin-connected rigid rods AB and BC are inclined at 0 the force P is applied, 0 becomes 32°.…

Concept explainers

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur, chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.

Question

The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30
mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa.
Neglect torsional effect.
400 mm
BC
The maximum safe value of Pis
30°
P
480 mm
kN. (Round off to one decimal place)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Solution

VIEW

Step 3: Calculations

VIEW

Step 4: Load calculation

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Ends A and D of the two solid steel shafts AB and CD are fixed, while ends B and C are connected to gears as shown. Knowing that a 6-kNm torque T is applied to gear B, calculate the maximum shearing stress (a) in shaft AB, (b) in shaft CD. 40 mm 384 mm C 200 mm 20mm 600 mm
Problem 2 (for all students). Determine the state of stress, the principal stress and the max in- plane shear stress at point B on the cross section of the pipe at section a – a. Indicate the results on a differential element at the point. a 300 mm B, 300 mm a |6 kN B.50 mm TA - 40 mm Section a - a
observe the given values carefully and give me right solution with clear calculations. Don't copy from other experts solution
hello dear expert, please help me to solve this question its my homework i have very limited time.
In the following structure, consider the following data: The connection at D is double and has a diameter of 50 mm. The beam BCDE has a thickness of 37.50 mm. The bar AB has a thickness of 37.50 mm and a width of 100. The connection at A is single and has a diameter of 67.50 mm. a. The normal stress in bar AB. Answ. 3.53 MPa b. The shear stress in the bolt at D. Answ. 6.25 MPa c. The shear stress in the bolt at A. Answ. 6.25 MPa d. The support stress between the beam and bolt D. Answ. 13.08 MPa
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.201 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=19 kips, Q=13 kips, L1=7 ft, L2=9 ft, and L3=9 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
ECCENTRIC SHEAR ON BOLTS: THE GUSSET SHOWN IN FIGURE IS RIVETED TO THE COLUMN FLANGE BY 16 – 22 mm DIAMETER RIVET IN SINGLE SHEAR. DETERMINE THE STRESS IN THE MOST HEAVILY LOAD RIVET.
Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined together by a pin with a diameter of 60mm. 200 mm 60 mm P 160 mm T 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250MPA and the shear strength of the pin is 100MPA. Suppose that P is 140KN, the Modulus of Elasticity is 200GP,, and the Poisson's ratio is 0.3. 2) Determine the change in length of each plate. 3) Determine the change in width of each plate. 4) Determine the change in thickness of each plate.
If couple forces of F = 35 N are applied to the handle of the machinist’s vise, determine the compressive force developed in the block. Neglect friction at the bearing A. The guide at B is smooth. The single square-threaded screwhas a mean radius of 6 mm and a lead of 8 mm, and the coefficient of static friction is μs = 0.27.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. STRENGTH OF MATERIALS The piece of plastic is originally rectangular. After the application of force, it deformed in the position shown. If a = 2 mm, b = 1.5 mm, and c = 4 mm, determine the normal strain in diagonal BC and the shear stress in corners A and C.
06 ameter against Es P are Q13. A torque T = 5 kN.m is applied to a hollow shaft having the cross section shown. Neglecting the effect of stress concentrations, determine the shearing stress at points a and b. welded owable nissible 10 mm 6pm 125 mm 6 mm 10 mm 75mm Q14. A hollow member having the cross section
How do I solve this using Mohr’s Circle