(c) A thin, triangular plate ABC is uniformly deformed into a shape ABC', as shown by the dashed lines in the figure. Calculate (i) The normal strain along the centreline OC; (ii) The normal strain along the edge AC; and (iii) The shearing strain between the edges AC and BC. b 0-1 b B 90° 10.001b

(c) A thin, triangular plate ABC is uniformly deformed into a shape ABC', as shown by the dashed lines in the figure. Calculate (i) The normal strain along the centreline OC; (ii) The normal strain along the edge AC; and (iii) The shearing strain between the edges AC and BC. b 0-1 b B 90° 10.001b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length.
4
We are given the statically indeterminate structure shown in Figure 2. Apart from the loadings, member AB is also subjected to temperature effects. The cross-sectional depth of member AB is h = 12 in, and the thermal coefficient is aT= 5:10-6 /° F. We are also given that the effect of axial forces on the deformations can be NEGLECTED. 1 kip/ft 5 kip BV VVvvvwwW EI = 8:105 kip-ft2 EI = 106 kip-ft2 20 ft Figure 2 a) Establish a primary structure b) Establish the compatibility equation from which you will obtain the redundant force c) Determine the support reactions of the structure d) Determine the internal loading diagrams of the structure e) Determine the support reactions IF THE STRUCTURE IS ONLY SUBJECTED TO THE TEMPERATURE EFFECTS (and not the loads) AT: = 5 °F ÅT;= -5 °Fi
Find the mayximum bending stress 75 N/m 60° N/m 2) 5m Ø Icm
4. Part AB of the bar has a solid circular cross section and part BC has a hollow circular cross section. The bar is fixed at both ends and a 150-in-kip axial torque is applied at B. Suppose that you want to decrease the weight of the bar by increasing the inside diameter of part B. The bar is made of material that will safely support a pure shear stress of 10 ksi. Based on this criterion, what is the largest safe value of the inside diameter? 4 in 2 in 150 in-kip A -14 in 7 in
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Calculate the shear strain, Yxy, at A. Also, calculate the average normal strain & along the x' axis. 800 mm 45% 45° 800 mm 5 mm
A thin triangular plate ABC is fixed on side AB. The plate is strained such that all straight lines in the plate remain straight after deformation and that apex C is displaced to point C'as shown. Compute the following: a) the normal strains ex, ey and the shearing strain yxy at point C based on small deformation theory b) the normal strain at point A in the direction of AC based on small deformation theory c) the normal strains ex, ey and the shearing strain yxy at point C based on large deformation theory A 30° -200 mm. 3mm C" 1 I 1 1 60° 4mm
5 in? in. 3 in? 1 in? 500 lb. 1500 Ib. 20 in. 20 in. 20 in. E = 29 x 106 psi Member 1 2 3 a) Develop the system stiffness matrix for the three element bar shown. b) Use the applied loads and boundary condition to develop the restrained system stiffness matrix with the applied loads c) Find the deflections at each node d) Solve for the internal forces in each rod element e) Compute the strain energy in the structure. f) Verify the results that you found for c) by using classical approach, õ=(P.L)/(A.E)
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.18 in. In segment (2), the normal strain is measured as 1,650 pin/in. Assume L₁ - 34 in. and L₂-83 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) Answers: (a) in.& (b) = 4 i B (2) 4₂ in, pin/in.
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X