Transformations (strain) Q43A strain guage rosette is placed on the outside surface of a loaded componentThe rossette has three guages aligned at 0, 45 and 90 degress.The microstrain readings are 578, 57 and 947 respectively.Use these readings to determine:the Maximium in-plane Principal Strain (Answer in microstrain).the Minimum in-plane Principal Strain (Answer in microstrain).the Principal Angle (Answer in degress).the Maximum in-plane Shear Strain (Answer in microstrain).Select the 4 correct answers from the list below/:a. 2041.83268658331b. 53.2384648095396c. 39.9288486071547Od. 46.5836567083472e. 2088.41634329165f. 1193.38076759523g. 26.6192324047698Oh. 1790.07115139285Oi. 1750.14230278569Oj. 22.6033254987178Ok. 1166.76153519046I. 2386.76153519046Om. 875.071151392846n. 7.53444183290595✓o. 1458.45191898808p. 30.1377673316238q. 33.27404050596231491.72595949404O s. 15.0688836658119✔t. 37.6722091645297

Given data εx = 578 microstrain ( at θ = 0°) εy = 947 microstrain ( at θ = 90° ) εx' = 57…

Transformations (strain) Q43 A strain guage rosette is placed on the outside surface of a loaded component The rossette has three guages aligned at 0, 45 and 90 degress. The microstrain readings are 578, 57 and 947 respectively. Use these readings to determine: the Maximium in-plane Principal Strain (Answer in microstrain). the Minimum in-plane Principal Strain (Answer in microstrain). the Principal Angle (Answer in degress). the Maximum in-plane Shear Strain (Answer in microstrain).

Transformations (strain) Q43 A strain guage rosette is placed on the outside surface of a loaded component The rossette has three guages aligned at 0, 45 and 90 degress. The microstrain readings are 578, 57 and 947 respectively. Use these readings to determine: the Maximium in-plane Principal Strain (Answer in microstrain). the Minimum in-plane Principal Strain (Answer in microstrain). the Principal Angle (Answer in degress). the Maximum in-plane Shear Strain (Answer in microstrain).

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 8CQ

See similar textbooks

Related questions

Q: *2-8. The rectangular plate is subjected to the deformation shown by the dashed line. Determine the…

A: The average shear stress is given by:

Q: [0.0016 [o] = 0.0003 0 0.0003 0.0008 0 0 0 0.0004. a. Determine the strain matrix for this strain…

A: Data given Find: (a) Determine the strain matrix for the given strain state if the x and y axes…

Q: P2: A state of plane stress consists of an 8-ksi tensile stress (as shown) along with an unknown…

A: Consider σx=σo=8ksiσy=0τxy=τo

Q: Determine the orientation measured clockwise to the principal plane (in degrees). 2- Transform…

A: Normal and shear stress is given we can find unknown by analytically

Q: Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a…

A: The expression of shear strain at point E is given as γx'y'=εx-εysin 2θ+γxycos 2θ Here εx is the…

Q: If the state of stress on the element is 4.5 MPa in each direction, find oavg. O 4.5 MPa 9 MPa O Mpa…

Q: 2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in…

Q: what differ between plane stress and strain.As like pancel is which of those? （eg,a pancil ,glass…

A: Given data: Difference between Plane stress and Plane strain.

Q: q19At a point in a two dimensional stress system, the normal stress on two mutually perpendicular…

Q: 4. The state of strain at a point on the clamp has components of Yay=-500(106), &y=+500(106), and…

A: Solution: Given: γxy=-500×10-6 εx=-600×10-6 εy=500×10-6

Q: Part B - The internal reaction at B Assume that the axial member is in equilibrium and the applied…

A: F3=3kN F4=2 kN

Q: An element is subjected to the following plane stress condition. The maximum principal stress in psi…

A: Given data : Normal stress in X direction=σXσX=20 psiNormal stress in Y direction=σYσY=0 psiShear…

Q: etermine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in…

A: All Data is given in the figureNeed to findThe shear strain at point A.The shear strain at point…

Q: A thin rectangular polymer plate PQRS of width b = 361 mmand height a = 193 mm is shown in the…

A: Determine the shear strain at corner P after the deformation.

Question

Transformations (strain) Q43
A strain guage rosette is placed on the outside surface of a loaded component
The rossette has three guages aligned at 0, 45 and 90 degress.
The microstrain readings are 578, 57 and 947 respectively.
Use these readings to determine:
the Maximium in-plane Principal Strain (Answer in microstrain).
the Minimum in-plane Principal Strain (Answer in microstrain).
the Principal Angle (Answer in degress).
the Maximum in-plane Shear Strain (Answer in microstrain).
Select the 4 correct answers from the list below/:
a. 2041.83268658331
b. 53.2384648095396
c. 39.9288486071547
Od. 46.5836567083472
e. 2088.41634329165
f. 1193.38076759523
g. 26.6192324047698
Oh. 1790.07115139285
Oi. 1750.14230278569
Oj. 22.6033254987178
Ok. 1166.76153519046
I. 2386.76153519046
Om. 875.071151392846
n. 7.53444183290595
✓o. 1458.45191898808
p. 30.1377673316238
q. 33.2740405059623
1491.72595949404
O s. 15.0688836658119
✔t. 37.6722091645297

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Estimate the elastic and plastic strain at the ultimate tensile strength in the low-carbon steel specimen in Figure 6.16.
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG