13. A block 100mm x 100mm base and 10mm height. What will the direct shear stress in the element when a tangential force of 10kN is applied to the upper edge to a displacement 1mm relative to lower face?

Q: Situation 41, 42 and 43 20 MPa 80 MPa 80 MPa 20 MPa O Zoom image Determine the normal stress along…

A:

Q: 250mm P 50mm 250mm B 50mm 2 m 2 m 50mm 400 mm

A:

Q: 17 MPa 27 MPa 56 MPa

A:

Q: A cube (E - 20OGPA) is experiencing stress from all directions. Along the x-direction, there is a…

A:

Q: 2. A finite element analysis of a bearing housing indicates that at a point p, the material is…

A: Principle stresses are the those stresses that are to the normal with zero plane. The value of…

Q: Q/Normal and shear stresses acting at the point is shown in Figure 1- Determine the principal…

A:

Q: -termine the principal stresses, the maximum in plane d average normal stress. Specify the…

A: Since this a multiple question as per Bartleby policy, we can answer only first question, for other…

Q: 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

A:

Q: 12 mm 12 mm 276 mm NA.- 12 mn 150 mm

A:

Q: What is the stress at the section x - x. for the bar ABCD with uniform cross-section 1000 mm²? с A…

A:

Q: The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average…

A:

Q: A P Front view ---160 mm What is the stress in bar BD if P = 4 kips? B D 12

A: Given: P=4kips

Q: A 116.79 kips (B 172.79 kips 92.79 kips A 119.38 kips B 40 kips 1.5" V 40 kips C From the figure,…

A: dia of rod AB=2''allowable stress in rod AB=55ksi

Q: The solid circular cross section of R = 8cm radius is subjected to torsional moment M2 = 60kNcm. The…

A:

Q: Find normel stress at pontA ? Find shear stren at puint A point A ? 2

A: We have to find Normal and Shear stresses at point A

Q: A flat bar of a width b = 60 mm and thicknesst = 10 mm is loaded in tension by a force P…

A: (a) Determine the pin diameter dmforwhich the load P is a maximum.(b)Determine the value of maximum…

Q: A flat steel bar, 27 mm wide by 2 mm thick and 1.6 m long, is bent by couples applied at the ends so…

A:

Q: Determine the a) magnitude load P to be applied, and b) the normal stress on plane AB and the…

A:

Q: Solve all reactions and the forces in every member.

A: The combination of two or more straight structural members connected by therE ends commonly…

Q: I The force on the 12mm thick link in the figure shown is 2960 N. If the pin has a diameter of…

A: Given,  Thickness = 12 mm Force = 2960 N Diameter of pin  = 10 mm

Q: Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal…

A:

Q: 1. A steel bar has a uniform cross sectional area of 300mm². Calculate the stress at member AB. 1.6m…

A: Given data,  Area = 300 mm²   To find out the stress at AB.

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD2- if Beam Weighs is not know then finding of…

Q: -0/02 -400 m

A:

Q: The bar ABC is fixed at A and restricted at C by two 16-mm diameter vertical steel bars, 1500 mm…

A:

Q: For an element subjected to ox = 40 MPa (compressive), oy = 30 MPa (tensile) and txy = +20 MPa, the…

A:

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine loadP that can…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A:

Q: The cantilever beam, whose loading condition and cross-section are given in the figure, is ideal…

A:

Q: For the element with stresses as shown below, find: . The magnitudes and directions of major and…

A: To determine-

Q: Find stress Force 1 N Cross sectional Area=0.2 mm2

A: Introduction : The given question is related to solid mechanics . In this question we are provided…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: (a) Stresses :σx=24 ksiσy=-72 ksiτxy=36 ksi

Q: Given the following technical description, determine if the traverse is closed. If not, balance the…

A:

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A:

Q: SITUATION. A square post is made up of two parts glued at an angle of 30 from the vertical axis.…

A:

Q: Combined Stress: 17a The cantilever beam shown below is loaded by P=20 kN load as shown. Find at…

A: Load, Normal stress, Width of section, Depth of section, To find: The angle to produce zero normal…

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.