P

Q: Find

A:

Q: The section of a thick beam has the dimensions Calculate the section properties I,, I, and I,…

A: The direct stress is generally produced by bending moments or by the bending action of shear loads…

Q: A bar of a uniform cross-section is rigidly fixed at one end and loaded by an off-centre tensile…

A: Given h=18mm b=37 mm σ=234MpaF = 1.5 KN Since you have posted a question with multiple sub-parts, we…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A:

Q: The aluminum rod AD (E=73 GPa, a=23×10-6/ºC) has a diameter of 15 mm and is attached to the rigid…

A: Determine: a) The location and magnitude of the maximum stress acting on the rod AD b) Displacement…

Q: "he tensile stress-strain curve of a polymer may be represented by o=a rue stress and e is the…

A: Given: from the stress strain definition we have to remember the concept  concept for stress strain…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 2 m 1m 25KN The thickness…

A:

Q: 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

A:

Q: E, 45° 45°

A: Calculate the strain in x-direction:…

Q: A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see…

A: Given:- E = 210 GPa σY =820 MPa L =1.0 m diameter is d =3 mm To find:- (a) Assuming n = 0.2,…

Q: (6) A bar of steel has the minimum properties S. = 276 MPa, S, = 413 MPa, and Su = 551 MPa. The bar…

A: Modified Goodman criterion : The Goodman relation (also known as a Goodman diagram, a Goodman-Haigh…

Q: The bronze bar 5 m long with a cross sectional area of 425 mm² is placed between two rigid walls as…

A: Given, Length of the bronze bar, L= 5m Area, A= 425 mm2 Gap at temperature of -20°C, ∆= 3.8mm…

Q: Write the equation for finding the principal stresses

A: Given data in question  Principal stress  To find out  Equation for Principal

Q: Below is another BA bar attached to the AD bar. Diameter of DA bar is 0.02M. A force F = 1000N is…

A:

Q: Obtain the maximum bending moment Mx that the cross section given below can safely carry. The…

A: Sigma=100MPa

Q: *2-32. The rectangular plate undergoes a deformation shown by the dashed lines. Determine the shear…

A: Shear strain refers to the relative displacement in relation to a fixed layer in any perpendicular…

Q: - 3 m- ak

A:

Q: Prob. 3.4-6. A magnesium-alloy rod (E = 6.5 x 10 ksi) o × 11 15 x diameter d. 1 in. is encased by a…

A:

Q: Find the strain in rod Stress 23 MPa E-45 MPa

A: step 1-

Q: The state of stress at a point in a structural member may be represented by a two-dimensional stress…

A:

Q: The 2D stress at a point is given by the matrix 50 15 Oxx Oxy МРа 15 10 Oxy Oyy The maximum shear…

A: To get maximum shear stress, first we have to calculate major and minor principal stress. Then…

Q: An element in plane stress is subjected to stresses o, = -52.7 MPa and Txy = 41 MPa (see figure). It…

A: The stress element is shown in the figure.

Q: Bending stress increases when the cross- sectional area increases. Select one: O True O False

A: It is required to answer whether the given statement is true or false.

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: Determine the largest torque Tmax that can be applied at the upper end of the steel rod.

Q: bronze rod. Axial loads are indicated. Find the maxim exceed a stress of 80MPa Mpa in bronze. -1.0m…

A:

Q: Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and…

A:

Q: Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2

A: Introduction : The question is related with solid mechanics . In this question the data of tensile…

Q: An aluminum [E = 11100 ksi] control rod with a circular cross section must not stretch more than…

A: Given data,  Stress = 10.8 ksi E = 11100 ksi P = 2090 lb

Q: For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is…

A: A state of stress is given as shown in the figure-To Find-The value of the maximum shear stress.

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: The rigid bar of ABCD of negligible weight is supported hinge at A, steel rod at B and bronze rod at…

A:

Q: 120 mm 750 mm 300 mm 1.0 mm

A: Given data  Triangular shape Dimensions  To find  Shear strain

Q: The state of 2D stress at a point is given by a matrix 100 30 MPа 30 20 xy Tyx Oy Тух буу The…

A:

Q: The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls.…

A:

Q: Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2

A:

Q: A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0625-in. to new…

A:

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are…

A:

Q: The section of a thick beam has the dimensions shown in the figure below. Calculate the section…

A:

Q: A rigid bar ABCD is supported by two bars as shown in Figure below. There is no strain in the…

A: Determine: a. The normal strain in bar (2). b. The normal strain in bar (2) if there is a 1 mm gap…

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.