The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls. At a temperature of – 20 °C, there is a gap of 2.20 mm. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18x10/°C and E = 80 GPa. L = 3.0 m 2.20 mm

The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls. At a temperature of – 20 °C, there is a gap of 2.20 mm. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18x10/°C and E = 80 GPa. L = 3.0 m 2.20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
Steel bar of cross-section 550mm2 is acted upon by the forces shown in figure. For steel, E = 200GPa. Compute the stress in BC Compute deformation of AB Compute the total elongation of the assembly.
2. Solve for the deformation of the aluminum rod. 200 mm 300 mm 600 kN Aluminum E= 70 GPa A= 900 mm Steel E= 200 GPa A=1200 mm
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
At a temperature of 27.89 °C a 0.41-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 126.64°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 320.36 mm and M = 231 mm. Round off the final answer to four decimal places. d ... M A B Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/C A = 800 mm² E = 190 GPa %3D a = 17.3 × 10-6/°C
A rigid bar of negligible weight is supported and loaded with 70 kN, compute the temperature change AT (°C) that will cause the stress in the bronze rod (L = 1.5 m, A = 300 mm?, and E = 83 GPa) to be 50 MPa. Assume a = 18.9 µm/(m°C) for bronze and 12.8 um/(m°C) for aluminum (L = 3 m, A = 750 mm2, and E = 70 GPa). Aluminum Bronze 2.5 m 1.5 m 70 kN
2.75 A steel rod is stretched between two walls. At 20°C, the tensile force in the rod is 5000 N. If the stress is not to exceed 130 MPa at –20°C, find the minimum allowable diameter of the rod. Use a = 11.7 × 10–6/°C and E = 200 GPa. %3D
At a temperature of 28.42 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 137.38°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 339.61 mm and M=240 mm. Round off the final answer to four decimal places. d ... В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6°C
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 185 mm, a wall thickness of 5 mm, and a length of 5.0 m. The pipe supports a compressive load of 675 kN. After the temperature of the pipe drops 39°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
2. A copper rod of diameter 12 mm is subjected to a compressive force of 8 kN. The change in diameter happens to be 4.5 x 103 mm. Determine the strain along the length of the material and the Poisson's ratio when E = 110 GPa.
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?