Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.

Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage of gas under pressure of 2.2 MPa. a. Determine the value of the tangential stress in the tank wall Determine the value of the longitudinal stress in the tank wall b. 30 mm helt hand
Rigid bar ABCD is loaded and supported as shown. Steel [E = 27800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.63 in.2 and bar (2) has a cross-sectional area of 0.39 in.2. After load P is applied, the strain in bar (1) is found to be 720 με. Assume L1=56 in., L2=89 in., a=30 in., b=37 in., and c=33 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
Required information Consider the given state of stress. Take A= 16 MPa and B= 48 MPa. В A 60 MPа Determine the principal planes. The principal planes are at and
Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a 22-mm-square bar of alloy and the load P is 20.15 kN. Express your answer in two decimal places.
B3
A Plane stress state is given on a material element as shown below. Os1-a+b+h T1=27 (MPa), on=b+c+d+h (MPa), ti2=c+g+h+d (MPa), O"=2(T1), E= 1000(T1) Mpa, v=(T1)/100 a) Calculate stresses (normal and shear) on AB surface. b) Find principal stress values and their directions (w/ respect to normal n of the AB surface). ) Find maximum in-plane shear stress and its direction (w/ respect to normal n of the AB surface). d) Find the volumetric and distortion strain energy densities at this point. 011=17 022=20 112= 14
Part 2,3,4
Q2: For the stresses at the point shown, find: • The maximum shearing stress. • The principal stresses and planes. 12 ksi 8 ksi 6 ksi
Please solve quick
9. The initially square element of a material is deformed as shown. Determine the shear strain of the element and the normal strains of the diagonals AC and BD. Undeformed Deformed A B D 2.0 mm 2.015 mm C 1.995 mm
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.45 in.2. After load P is applied, the strain in bar (1) is found to be 850 μεμε. Assume L1=53 in., L2=79 in., a=34 in., b=33 in., and c=30 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m