Problem (1) Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm? cross-sectional area and rod EF has a 600 mm? 500 mm cross-sectional area. В (a) statically determinate or indeterminate. Why? (b) stress in each rod. State whether the structure is E 400 mm Determine the force and the OF Determine the deformation of each rod. (c) Note: The link BED is rigid, and BE = ED.

Problem (1) Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm? cross-sectional area and rod EF has a 600 mm? 500 mm cross-sectional area. В (a) statically determinate or indeterminate. Why? (b) stress in each rod. State whether the structure is E 400 mm Determine the force and the OF Determine the deformation of each rod. (c) Note: The link BED is rigid, and BE = ED.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: o Given: A stepped shaft with the following properties Copper: A = 2 in² E = 16 × 106 psi Steel: A =…

A: Given Copper and steelArea and Elasticity modulus of copper is 2 in2 and 16×106 psiArea and…

Q: "he tensile stress-strain curve of a polymer may be represented by o=a rue stress and e is the…

A: Given: from the stress strain definition we have to remember the concept concept for stress strain…

Q: Shafts A and Bare made of the same material and have the same cross-sectional area, but A has a…

A: Given:The shafts A and B are having same cross-sectional area According to the problem statement, we…

Q: a) The principal planes b) The principal stresses c) The stress components exerted on the element…

A: Question is based on the element subjected to axial, compression and shear stress . Magnitude of…

Q: El is constant, find the reaction forces. Using the method of consistent deformations

A: Calculation of Reactions at Supports using method of consistent deformation or Force method of…

Q: A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an…

A: Detailed solution is provided below :

Q: Obtain the maximum bending moment Mx that the cross section given below can safely carry. The…

A: Sigma=100MPa

Q: *2-32. The rectangular plate undergoes a deformation shown by the dashed lines. Determine the shear…

A: Shear strain refers to the relative displacement in relation to a fixed layer in any perpendicular…

Q: When force P is applied to the rigid arm ABC, point B displaces vertically downward through a…

A: To find the normal strain in wire CD, we need to determine the elongation of wire CD caused by the…

Q: d. the normal stress in region BC. Is the material within its linear-elastic region? Yes / No A…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods DE and a pin support at…

A: Draw free body diagram From deflected shape δAB8=δP4=δDE6=tanθ Consider the moment equilibrium…

Q: The steel used for the step shaft has an allowable shear stress of Tallow radius at the transition…

Q: I'm A Fi m B m C m 3 m P (100+K) kN A rigid AD bar is suspended by two wires as shown in the figure.…

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

Q: 2) The horizontal beam is rigid, and the three bars have the same length. The bars AB and EF are…

A: Given- AB and EF made of aluminium, CD is made of steel, Structure is heated from 50 oF to 90 oF.

Question

Problem (1)
Three steel rods (E = 200 GPa) supports a 50 kN
load P. Each of the rods AB and CD has a 300 mm?
cross-sectional area and rod EF has a 600 mm?
500 mm
cross-sectional area.
В
(a)
statically determinate or indeterminate.
Why?
(b)
stress in each rod.
State whether the structure is
E
400 mm
Determine the force and the
OF
Determine the deformation of each rod.
(c)
Note: The link BED is rigid, and BE = ED.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
A stress developed if the applied force is parallel to the resisting area refers to: O tangential O bearing O normal. O simple
3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa 4. In question 3, assume that the bar is free to elongate or shorten, calculate the change in the length of the bar if the temperature drops from 20°C to -20°C.