3.18 The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.

3.18 The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two identical plates are connected by two 18-mm diameter rivets as shown. Consider the following dimensions: B = 200 mm t = 22 mm x = 16 mm The allowable stresses of the plate are the following: Normal stress = 18 MPa Bearing stress = 4 MPa Shearing stress = 5 MPa Determine the maximum force P: A. Considering the normal stress: P = B. Considering the bearing stress: P = C. Considering the shearing stress: P = Express your answers in three decimal places. KN kN KN O CHEGG.CO ISL STRI NG URVE VARSITY TUTUP INST UTORIAL TE SUCH, B O CHEGG COURSEHERO, SKOOLI TUTORET TUTURME VARSITY TUTORS, WZANT. ETC. DISTRIBUTION TO ANY PARTY IS PROHIBITED, INSTITUTIONAL EXAM NOT EUPLOADING ON ANY TUTORIAL SITE SUCH LEDO CHEGG, COURSEHERO, SKOTTOREYZ TUTORM VARSITY TUTORS, W ZAWI, ETC. P4 DISTRIBUTION TO ANY PARTY IS PROHIBITED. NOT P SN INSTITUTIONAL EXEM NOT FOR REUPLNG ON ANY TUTORIAL SITE SUC 30 CHEGG, COURSEHERO, SKOOL TUTO+STORM VARSITY TUTORS, W DISTRIBUTION TO ANY RTY IS PROHIBITED. THERO, SKOOL…
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
I need to solve the question in the strength materials
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe. at section a-a. mun 40 mm 300 mm 300 mm
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.18 in. In segment (2), the normal strain is measured as 1,650 pin/in. Assume L₁ - 34 in. and L₂-83 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) Answers: (a) in.& (b) = 4 i B (2) 4₂ in, pin/in.
THE BEAMS SHOWN IN FIGURES (a) AND (b) HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fy=400 MPa AND IS SUBJECTED TO A POSITIVE BENDING MOMENT Mu=140KN-m. ANSWER THE FOLLOWING.1. DRAW THE INTERNAL STRESS AND STRAIN DIAGRAM OF BEAM CONSIDERING THAT THE DEPTH OF THE STRESS BLOCK IS GREATER THAN THE THICKNESS OF THE FLANGE.