An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure. The length I of the member is 3 m. MT R Ri If a G1 = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in the tube. Select the correct response 77T

An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure. The length I of the member is 3 m. MT R Ri If a G1 = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in the tube. Select the correct response 77T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q- A stepped steel shaft is subjected to a clockwise torque of 10 Nm at its free end. Shear modulus of steel is 80 GPa. Find the strain energy in the shaft? A 50 mm dia 100 mm B 25 mm dia 100 mm C K T=10 Nm
The shaft shown consists of a steel tube (1) bonded to a brass core (2). The shear modulus of steel is 11,400 ksi and the shear modulus of brass is 5,200 ksi. A torque is applied at A. The radius of the brass core is 0.5 in. The outer radius of the steel tube is 1 in.d) Assume the allowable shear stress in the brass core is 450 psi. Calculate the maximum torque you could apply to the system in k-in.e) Assume that the maximum angle of twist at the free end is not to exceed 0.05 rad. Calculate the maximum torque you could apply to the system in k-in.f) Based on your answers from parts (c)-(e), what is tha maximum torque (in k-in) you could apply to the system using a factor of safety (FOS) of 2?
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=79, T2 =14, T3 =23 Note: round off your answer to whole number T2 Nm | T3 Nm T1 Nm
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1260 μm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. 1413 μm/m 1223 μm/m 1286 μm/m 738 μm/m 1553 μm/m
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
Below is another BA bar attached to the AD bar. Diameter of DA bar is 0.02M. A force F = 1000N is applied in the negative x direction at the end of the DA bar and a force P = 500N in the negative y direction at point B. Assuming that the DA bar is made of a ductile metal, find the safety coefficient of the bar by calculating the Von Mises stress at O point. (AD bar material is cold drawn AİSİ 1040 steel.)
A hollow aluminum tube used is a roof structure has an outside diameter d2 and inside diameter d1. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.If the tube is twisted in pure torsion by torques acting at the ends,what is the angle of twist in degrees when the max shear stress is 50MPa? b.What diameter “d” is required for a solid shaft to resist the same torque with the same maximum stress? d1 = 90 (mm) d2 = 110 (mm)
Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods AB & DE and a pin support at C. Bar ACD was horizontal prior to the application of load P. The tensile strain measured in rod AB after the application of the load is ɛ1= 0.003. Determine the rotation 0 of the bar ACD and the normal strain in rod DE. Also calculate the value of load P for these deformations. The diameters of rod AB and DE are 1.5 in. and 2 in, respectively. P - 4 ft 4 ft- 6 ft A Rigid (2) 6 ft 8 ft (1) E В
The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable shear stress of 6 ksi. The diameter of the rod is d1 = 0.500 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
Problem 1 A rigid bar AC is loaded and supported as shown. Bar AB and CD are unstressed before the load is applied. Bar AB is made of steel (E = 30000ksi) and has a cross-sectional area of 1.25 in?. Bar CD is made of brass (E = 15000ksi) and has a cross-sectional area of 0.75 in². Determine: %3D 12 k/ft (1) The stresses in bars AB and CD (2) The vertical displacement (deflection) of C relative to the displacement at point (Note: express your answer in inches and include a direction) TI!||! 3 ft 4.5 ft
Weight at B = 40kn and at C is 30Kn