The wire BC has a diameter of 0.175 in. and the material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle at D if the pull at the grip is slowly increased and reaches a magnitude of (a) P= 480lb, (b) P= 700lb. Assume the bar is rigid.

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe

A: take stresses in Rod and Pipe as Equal Take sum of forces as 8KN Take moment about rod as 0

Q: 30 mm 80 mm

A: Use Elastic Moment Formula

Q: 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

A:

Q: Shafts A and Bare made of the same material and have the same cross-sectional area, but A has a…

A: Given:The shafts A and B are having same cross-sectional area According to the problem statement, we…

Q: A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see…

A: Given:- E = 210 GPa σY =820 MPa L =1.0 m diameter is d =3 mm To find:- (a) Assuming n = 0.2,…

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A:

Q: The bronze bar 5 m long with a cross sectional area of 425 mm² is placed between two rigid walls as…

A: Given, Length of the bronze bar, L= 5m Area, A= 425 mm2 Gap at temperature of -20°C, ∆= 3.8mm…

Q: Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

A:

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: Given: P = 230KN, d = 24mm, a = 160mm, b = 260mm

Q: After load Pis applied to the pin-connected structure shown, a normal strain of ɛ= + 770 uɛ is…

A: Given data Normal strain = 770 × 10 -6  in /in  E= 29000 ksi  Yield strength = 42 ksi

Q: Obtain the maximum bending moment Mx that the cross section given below can safely carry. The…

A: Sigma=100MPa

Q: A flexible connectoin consisting of rubber pads (thickness t = 9 mm) bonded to steel plates is shown…

A:

Q: Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice…

A: Consider the figure,

Q: - 3 m- ak

A:

Q: Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point…

A: Mohr’s Circle- It is the locus of points showing the magnitude of normal and shear stress at…

Q: Asmall aluminum alloy [E = 74 GPa] tee shape is used as a simply supported beam as shown. For this…

A:

Q: Bending stress increases when the cross- sectional area increases. Select one: O True O False

A: It is required to answer whether the given statement is true or false.

Q: At an axial load of 26 kN, a 35-mm-wide by 15-mm-thick polyimide polymer bar elongates 2.9 mm while…

A: Answer  (a) We know that Modulus of Elasticity is given by E = σε σ = stress σ = loadArea…

Q: The bronze bar 3 m long with a cross-sectional area of 350 mm? is placed between two rigid walls. At…

A: Given, l=3 mA=350 mm2T1=-20° Cδ=2.2 mmα=18×10-6 /° CE=80GPaσ= 30 MPa

Q: bronze rod. Axial loads are indicated. Find the maxim exceed a stress of 80MPa Mpa in bronze. -1.0m…

A:

Q: Using an Permissible stress of 155 MPa, determine the maximum bending moment M that can be applied…

A: Given,  An, I section beam, Allowable stress, σ = 155mpa Find out:- maximum bending moment,

Q: A small aluminum alloy [E = 79 GPa] tee shape is used as a simply supported beam as shown. For this…

A:

Q: An aluminum [E = 11100 ksi] control rod with a circular cross section must not stretch more than…

A: Given data,  Stress = 10.8 ksi E = 11100 ksi P = 2090 lb

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: b 7'

A:

Q: Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b)…

A: Given, A cantilever beam, Bending Moment = M = 12kNm(clockwise) Find out , Stress at point A and B?…

Q: The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and…

A: Given: The inner diameter of the pipe AB is 20 mm. The outer diameter of the pipe AB is 28 mm. The…

Q: The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls.…

A:

Q: 1. Establish stress equations for both bars in the two-bar assembly shown below which isloaded with…

A: The objective of the question is to establish stress equations for both bars in a two-bar assembly…

Q: Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b)…

A: Given :

Q: A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the…

A:

Pressure and Stress