P A (0) B (2) (3) FIGURE P1.6/7 P1.7 WP Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure P1.6/7. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 25 kips are applied at B, and two loads of R35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 20 ksi. The normal stress magnitude in steel rod (2) must be limited to 35 ksi. The normal stress magnitude in brass rod (3) must be limited to 25 ksi. Determine the minimum diameter required for each of the three rods.

P A (0) B (2) (3) FIGURE P1.6/7 P1.7 WP Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure P1.6/7. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 25 kips are applied at B, and two loads of R35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 20 ksi. The normal stress magnitude in steel rod (2) must be limited to 35 ksi. The normal stress magnitude in brass rod (3) must be limited to 25 ksi. Determine the minimum diameter required for each of the three rods.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

#1 will upvote anyone who will answer
Determine the maximum tensile stress in the beam shown.
A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
4. A rigid block of having a weight M is suspended by symmetrically placed rods. Each copper rod has an area of 1200 sq.mm: E= 125,000 MPa and the allowable stress is 90 MPa. The steel rod has an area of 1500 sq.mm; E 220GPa; and the allowable stress is 120 Mpa. Determine the largest weight M which can be supported by the rods. 8c=8s Copper 160 mm Pc Ps Steel 240 mm TIT Pc ..initial level Tinal level Copper 160 mm
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
d = 600 6Ø28 75 75 300 can you please show how to find the elastic stress and design ratio? fc' = 27 MPa; M1 = 60 KN-m; M2 = 200 KN-m
Determine (d) variable stress and (e) design factor
The general stress element shown is loaded such that o = 20 MPa, oy = -20 MPa, Txy = 10 MPa. What is the max dy 1 xy 70x
Solve it
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d, = 1.5 in.; both have length L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P