A 1:50-scale model of a submarine is to be tested in a towing tank under two conditions: motion at the free surface and motion far below the surface. The tests are performed in freshwater. On the surface, the submarine cruises at 24 knots. At what speed should the model be towed to ensure dynamic similarity? Far below the surface, the sub cruises at 0.35 knot. At what speed should the model be towed to ensure dynamic similarity? What must the drag of the model be multiplied by under each condition to give the drag of the full-scale submarine?
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Additional Engineering Textbook Solutions
Fundamentals Of Thermodynamics
Applied Fluid Mechanics (7th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Mechanics of Materials
Mechanics of Materials (10th Edition)
- The aerodynamic drag of a new sports car is to be predicted at a speed of 60.0 mi/h at an air temperature of 25°C. Automotive engineers build a one-third scale model of the car to test in a wind tunnel. The temperature of the wind tunnel air is also 25°C. The drag force is measured with a drag balance, and the moving belt is used to simulate the moving ground (from the car’s frame of reference). Determine how fast the engineers should run the wind tunnel to achieve similarity between the model and the prototype.arrow_forward2. A student team is to design a human-powered submarine for a design competition. The overall length of the prototype submarine is 4.85 m, and its student designers hope that it can travel fully submerged through water at 0.440 m/s. The water is freshwater (a lake) at T = 15 °C. The design team builds a one-fifth scale model to test in their university's wind tunnel, as shown in the Fig. A shield surrounds the drag balance strut so that the aerodynamic drag of the strut itself does not influence the measured drag. The air in the wind tunnel is at 25 °C and at one standard atmosphere pressure. At what air speed do they need to run the wind tunnel in order to achieve similarity? Take for water at T = 15 °C and atmospheric pressure, p = 999.1 kg/m³ and µ = 1.138 × 10-³ Pa.s. Take for air at T = 25 °C and atmospheric pressure, p = 1.184 kg/m³ and µ = 1.849 × 105 Pa.s. Wind tunnel test section V Poo, P Model Shield FD Drag balance Strutarrow_forward1:25 scale model of a submarine is tested at 180 ft/s in a wind tunnel using sea-level standard air. What is the prototype speed in seawater at 20°C for dynamic similarity? If the model drag is 1.6lb, what is the prototype drag?arrow_forward
- A student team is to design a human-powered submarine for a design competition. The overall length of the prototype submarine is 95 (m), and its student designers hope that it can travel fully submerged through water at 0.440 m/s. The water is freshwater (a lake) at T = 15°C. The design team builds a one-fifth scale model to test in their university’s wind tunnel. A shield surrounds the drag balance strut so that the aerodynamic drag of the strut itself does not influence the measured drag. The air in the wind tunnel is at 25°C and at one standard atmosphere pressure. At what air speed do they need to run the wind tunnel in order to achievesimilarity?arrow_forwardPlease show working out aND explain the bukingham theoremarrow_forwardA 1:4 scale torpedo model has been built. The prototype is expected to move at a speed of 6m/s in water at 15°C. What should be the velocity in the model if, a) the test is done in a stream channel at 15°C; and b) the test is done in a wind tunnel at 27°C and a pressure of 20 atm?arrow_forward
- The drag force of a new sports car is to be predicted at a speed of 65 mi/h at an air temperature of 25 C. Automotive engineers build a 0.333333333333333 scale model of the car to test in a wind tunnel. The temperature of the wind tunnel air is also 25 C. Determine how fast (in mi/h) the engineers should run the wind tunnel to achieve similarity between the model and the prototype.arrow_forwardusing pure water at 20°C. The velocity of the prototype in seawater (p = A 1/18 scale model of the submarine is to be tested in the water tunnel 1015 kg/m³, v = 1.4x106 m²/s) is 3 m/s. Determine: a) the speed of the water in the water tunnel for dynamic similarity D) the ratio of the drag force on the model to the drag force on the prototypearrow_forwardThe wave resistance of a model of a ship at 1/19 scale is 2 lbf at a model speed of 7 ft/s. What are the corresponding velocity and wave resistance of the prototype? Fp = lbfarrow_forward
- Here, a 1:10 scale prototype of a propeller on a ship is to be tested in a water channel. What would the rotating speed of the model be if the rotational speed of the p propeller is 2000 rpm, and if: (a) the Froude number governs the model-prototype similarity(b) Reynolds number governs the similarityarrow_forwardA student team is to design a submarine for a design competition. The overall length of the prototype submarine is 4.85 m. The prototype submarine is expected to moves through freshwater in the lake at 0.440 m/s. The student team builds a one-fifth scale model to test in their university's wind tunnel. Calculate the wind tunnel air speed in order to achieve similarity with the prototype submarine. For water at T= 15 °C and atmospheric pressure, the density is p = 999.1 kg/m³ and the dynamic viscosity is µ = 1.138 x 10³ kg/m-s. For air in the wind tunnel at T= 25 °C and atmospheric pressure, the density is p= 1.184 kg/m³ and the dynamic viscosity is µ = 1.849 x 10-$ kg/m's.arrow_forwardi need the answer quicklyarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY