Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 7, Problem 51P
A water pump with impeller diameter of 24 in. is to be designed to move 15 ft3/s when running at 750 rpm. Testing is performed on a 1:4 scale model running at 2400 rpm using air (68°F) as the fluid. For similar conditions (neglecting Reynolds number effects), what will be the model flow rate? If the model draws 0.1 hp, what will be the power requirement of the prototype?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A centrifugal pump, pumps water at 0.240 m3/s rotating at 1200 rpm, a prototype pump using 10 lit/s is to be tested. If the diameter of the model is 3 times the diameter of the prototype, at what speed should the prototype run, if the pump pumps oil at a head of 30 meters. (a)What would be the required horsepower to drive the model at an efficiency of 0.8? (b)What would be the required horsepower to drive the prototype?
A 1:10 model of a Francis turbine developed 0.5 kW under a head of 2.5 m at 480 rpm. The physical data are r1=1.5m, r2 = 0.4m, α1=15°, β2=135°. Find the speed of the prototype at a head of 20m.
Solve it on priority and correctly
Chapter 7 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 7 - The slope of the free surface of a steady wave in...Ch. 7 - One-dimensional unsteady flow in a thin liquid...Ch. 7 - In atmospheric studies the motion of the earths...Ch. 7 - Fluid fills the space between two parallel plates....Ch. 7 - By using order of magnitude analysis, the...Ch. 7 - Consider a disk of radius R rotating in an...Ch. 7 - An unsteady, two-dimensional, compressible,...Ch. 7 - Experiments show that the pressure drop for flow...Ch. 7 - At very low speeds, the drag on an object is...Ch. 7 - We saw in Chapter 3 that the buoyant force, FB, on...
Ch. 7 - Assume that the velocity acquired by a body...Ch. 7 - Derive by dimensional analysis an expression for...Ch. 7 - The speed of shallow water waves in the ocean...Ch. 7 - The speed, V, of a free-surface wave in shallow...Ch. 7 - The boundary-layer thickness, , on a smooth flat...Ch. 7 - The speed, V, of a free-surface gravity wave in...Ch. 7 - Derive an expression for the velocity of very...Ch. 7 - Derive an expression for the axial thrust exerted...Ch. 7 - Derive an expression for drag force on a smooth...Ch. 7 - The energy released during an explosion, E, is a...Ch. 7 - Measurements of the liquid height upstream from an...Ch. 7 - The load-carrying capacity, W, of a journal...Ch. 7 - Derive an expression for the drag force on a...Ch. 7 - A circular disk of diameter d and of negligible...Ch. 7 - Two cylinders are concentric, the outer one fixed...Ch. 7 - The time, t, for oil to drain out of a viscosity...Ch. 7 - You are asked to find a set of dimensionless...Ch. 7 - A continuous belt moving vertically through a bath...Ch. 7 - Derive an expression for the frictional torque...Ch. 7 - Tests on the established flow of six different...Ch. 7 - The power, P, required to drive a fan is believed...Ch. 7 - The sketch shows an air jet discharging...Ch. 7 - The diameter, d, of bubbles produced by a...Ch. 7 - Choked-flow nozzles are often used to meter the...Ch. 7 - A large tank of liquid under pressure is drained...Ch. 7 - Spin plays an important role in the flight...Ch. 7 - The power loss, P, in a journal bearing depends on...Ch. 7 - The thrust of a marine propeller is to be measured...Ch. 7 - The rate dT/dt at which the temperature T at the...Ch. 7 - When a valve is closed suddenly in a pipe with...Ch. 7 - An airship is to operate at 20 m/s in air at...Ch. 7 - An airplane wing of 3 m chord length moves through...Ch. 7 - A flat plate 1.5 m long and 0.3 m wide is towed at...Ch. 7 - This 1:12 pump model using water at 15C simulates...Ch. 7 - An ocean-going vessel is to be powered by a...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - A 1:3 scale model of a torpedo is tested in a wind...Ch. 7 - A flow rate of 0:18 m3/s of water at 20C...Ch. 7 - A force of 9 N is required to tow a 1:50 ship...Ch. 7 - An airplane wing, with chord length of 1.5 m and...Ch. 7 - A water pump with impeller diameter of 24 in. is...Ch. 7 - A model hydrofoil is to be tested at 1:20 scale....Ch. 7 - A ship 120 m long moves through freshwater at 15C...Ch. 7 - A 1:30 scale model of a cavitating overflow...Ch. 7 - In some speed ranges, vortices are shed from the...Ch. 7 - A 1:8 scale model of a tractor-trailer rig is...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - When a sphere of 0.25 mm diameter and specific...Ch. 7 - The flow about a 150 mm artillery projectile which...Ch. 7 - Your favorite professor likes mountain climbing,...Ch. 7 - A 1:50-scale model of a submarine is to be tested...Ch. 7 - Consider water flow around a circular cylinder, of...Ch. 7 - A 1:10 scale model of a tractor-trailer rig is...Ch. 7 - The power, P, required to drive a fan is assumed...Ch. 7 - Over a certain range of air speeds, V, the lift,...Ch. 7 - The pressure rise, p, of a liquid flowing steadily...Ch. 7 - An axial-flow pump is required to deliver 0.75...Ch. 7 - A model propeller 1 m in diameter is tested in a...Ch. 7 - Consider Problem 7.38. Experience shows that for...Ch. 7 - Closed-circuit wind tunnels can produce higher...Ch. 7 - A 1:16 model of a bus is tested in a wind tunnel...Ch. 7 - The propagation speed of small-amplitude surface...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
While cutting a piece of paper, a person exerts the two indicated forces on a paper cutter. Reduce the two forc...
Engineering Mechanics: Statics
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
ICA 8-54
When we drive our car at 100 feet per second [ft/s], we measure an aerodynamic force (called drag) of ...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Determine, g, which locates the centroidal axis z for the cross sectional area of the T-beam, and then find the...
Engineering Mechanics: Statics
The quantity ms into s.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- CH, CQ and n are functions of CP. Draw the dimensionless performance curves of the turbine on a single graph by makingthe necessary scalings. (Fit the curve by using the excel program for drawing. Also give the values you used for plotting inthe table) ÖN=5arrow_forward4. A pump is required to pump fresh water at a flow rate of 5000 m³/hour against a head of 8 mat a speed of 1500 rev/min. It is planned to test a scale model with a head of 2 m at a flowrate of 100 m³/hour under dynamically similar conditions (but neglecting changes in ReynoldsNumber). Determine: a) The speed at which the model must be run.b) The scale that must be used for the model.c) The mechanical power required to drive the model pump is found to be 680W at theoperating point. Calculate the power required to drive the full scale pump.d) After the full scale pump is fitted into the system it is found that the pump head risereally needs to be increased by 30%. At what speed should the full scale pump now berun at to achieve this head rise and what will be the new ideal flow rate and powerconsumption in order to match this operating condition?e) Briefly comment on the main advantages and limitations of testing a scale model toprove the performance of a larger prototype.arrow_forwardexpressed in rev/s. 4. A water turbine is to be designed to produce 27 MW when running at 93.7 rpm under a head of 16.5 m. A model turbine with an output of 37.5 kW is to be tested under dynamically similar conditions with a head of 4.9 m. Calculate the model speed and scale ratio. Assuming a model efficiency of 88%, estimate the volume flow rate through the model. It is estimated that the force on the thrust bearing of the full-size machine will be 7.0 GN. For what thrust must the model bearing be designed?arrow_forward
- A 2:1 scale model of a pump was tested in a laboratory at 900rpm, head 20m and discharge 10 l/s. If the speed of prototype was 1500rpm, determine the head and discharge.arrow_forwardA quarter scale turbine model is tested under a head of 36 m. The full scale turbine is required to work under o head of 100 m and to run at 428 rpm. At what speed must the model be run and if it develops 135 HP and uses 0'324 m3/ sec of water at this speed, what power will be obtained from the full scale turbine assuming that its efficiency is 3 per cent better than that of the model?arrow_forwardHANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.arrow_forward
- SAE 30 oil at 60 °F is pumped through a 4-ft-diameter pipeline at a rate of 6750 gal/min. A model of this pipeline is to be designed using a 1-in.-diameter pipe and water at 60 °F as the working fluid. To maintain Reynolds number similarity between these two systems, what fluid velocity will be required in the model? Vm= i ft/sarrow_forwardThe moment of the torpedo control unit in water was tested with a 1:8 scale scale model in a water tunnel of identical properties with a speed of 20 m/s if the measured moment in the model was 14 Nm. calculate 1) Determine the velocity of the prototype using the Reynolds number analogy. 2) Find the ratio of the forces occurring in the model and prototype. Using the analogy of Euler number 3) find the moment that occurred with the prototype.arrow_forwardLR = 5m, LG = 2.5m and LC = 1.1m Q2. The Skylark family of sounding rockets consisted of a number of variants (denoted Skylark 5, Skylark 7, and Skylark 12 respectively). These are illustrated on Page 3. The data given below is based on that for the rocket motors they used (all manufactured and named by what was Royal Ordinance – now part of Roxel): Raven XI Motor Total mass: 1280 kg Length = LR See Case Table (units are m) Diameter = 0.44 m Goldfinch IIA Motor Total mass: 420 kg Length = LG See Case Table (units are m) Diameter = 0.44 m Cuckoo IV Motor Total mass: 242 kg Length = LC See Case Table (units are m) Diameter = 0.44 m The payload mass which is additional to the motor masses is to be taken as 100 kg. (a) For the configurations of the three rockets shown on Page 3 in Fig. Q2: (i) Determine the Pitching/Yawing moment of inertia of each rocket about the base of each rocket. (ii) Explain how you could then find the the Pitching/Yawing moment of inertia of each rocket about its…arrow_forward
- SAE 30 oil at 60 F is pumped through a 6-ft diameter pipeline at a rate of 6650 gal/min. A model of this pipeline is to be designed using a 3-in diameter pipe and water at 60 F as the working fluid. To maintain Reynolds number similarity between these two systems, what fluid velocity will be required in the model? Answer: 0.0338 ft/s. Please show work.arrow_forwardA model of centrifugal pump coupled to 5.5 kW motor is found to deliver 15 litres/s ofwater against a head of 28 m at 1450 rpm. If the prototype is required to develop ahead of 60 m, determine its speed, power and flow capacity. A scale of 1:3 between model and protoytpe.arrow_forwardA one-fifth scale model of a water turbine is tested in a laboratory at T = 20°C. The diameter of the model is 8.0 cm, its volume flow rate is 17.0 m3 /h, it spins at 1500 rpm, and it operates with a net head of 15.0 m. At its best efficiency point, it delivers 450 W of shaft power. Calculate the efficiency of the model turbine. What is the most likely kind of turbine being tested?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license