Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 7, Problem 54P
A 1:30 scale model of a cavitating overflow structure is to be tested in a vacuum tank wherein the pressure is maintained at 2.0 psia. The prototype liquid is water at 70°F. The barometric pressure on the prototype is 14.5 psia. If the liquid to be used in the model has a vapor pressure of 1.50 psia, what values of density, viscosity, and surface tension must it have for complete dynamic similarity between model and prototype?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 1:30 scale model of a cavitating overflow structure is to be tested in a vacuum tank wherein the pressure is maintained at 140 kPa. The prototype liquid is water at 20°C. The barometric pressure on the prototype is 100 kPa. If the liquid to be used in the model has an absolute vapor pressure of 10.0 kPa, what values of density, viscosity, and surface tension must it have for complete dynamic similarity between model and prototype?
The drag force on a submarine, which is moving on the surface, is to be determined by a test on
a model which is scaled down to one-twentieth of the prototype. The test is to be carried in a
towing tank, where the model submarine is moved along a channel of liquid. The density and the
kinematic viscosity of the seawater are 1010 kg/m³ and 1.3x10-6 m 2/s, respectively. The speed
of the prototype is 2.6 m/s. Assume that F = f(V, L. g. p.), using pi-theorem and similarity
principle to:
a) Determine the speed at which the model should be moved in the towing tank.
b) Determine the kinematic viscosity of the liquid that should be used in the towing tank.
Please solve this problem, Thank you very much! Figure is attached
1. liquids in rotating cylinders rotates as a rigid body and considered at rest. The elevation difference h between the center of the liquid surface and the rim of the liquid surface is a function of angular velocity ?, fluid density ?, gravitational acceleration ?, and radius ?. Use the method of repeating variables to find a dimensionless relationship between the parameters. Show all the steps.
Chapter 7 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 7 - The slope of the free surface of a steady wave in...Ch. 7 - One-dimensional unsteady flow in a thin liquid...Ch. 7 - In atmospheric studies the motion of the earths...Ch. 7 - Fluid fills the space between two parallel plates....Ch. 7 - By using order of magnitude analysis, the...Ch. 7 - Consider a disk of radius R rotating in an...Ch. 7 - An unsteady, two-dimensional, compressible,...Ch. 7 - Experiments show that the pressure drop for flow...Ch. 7 - At very low speeds, the drag on an object is...Ch. 7 - We saw in Chapter 3 that the buoyant force, FB, on...
Ch. 7 - Assume that the velocity acquired by a body...Ch. 7 - Derive by dimensional analysis an expression for...Ch. 7 - The speed of shallow water waves in the ocean...Ch. 7 - The speed, V, of a free-surface wave in shallow...Ch. 7 - The boundary-layer thickness, , on a smooth flat...Ch. 7 - The speed, V, of a free-surface gravity wave in...Ch. 7 - Derive an expression for the velocity of very...Ch. 7 - Derive an expression for the axial thrust exerted...Ch. 7 - Derive an expression for drag force on a smooth...Ch. 7 - The energy released during an explosion, E, is a...Ch. 7 - Measurements of the liquid height upstream from an...Ch. 7 - The load-carrying capacity, W, of a journal...Ch. 7 - Derive an expression for the drag force on a...Ch. 7 - A circular disk of diameter d and of negligible...Ch. 7 - Two cylinders are concentric, the outer one fixed...Ch. 7 - The time, t, for oil to drain out of a viscosity...Ch. 7 - You are asked to find a set of dimensionless...Ch. 7 - A continuous belt moving vertically through a bath...Ch. 7 - Derive an expression for the frictional torque...Ch. 7 - Tests on the established flow of six different...Ch. 7 - The power, P, required to drive a fan is believed...Ch. 7 - The sketch shows an air jet discharging...Ch. 7 - The diameter, d, of bubbles produced by a...Ch. 7 - Choked-flow nozzles are often used to meter the...Ch. 7 - A large tank of liquid under pressure is drained...Ch. 7 - Spin plays an important role in the flight...Ch. 7 - The power loss, P, in a journal bearing depends on...Ch. 7 - The thrust of a marine propeller is to be measured...Ch. 7 - The rate dT/dt at which the temperature T at the...Ch. 7 - When a valve is closed suddenly in a pipe with...Ch. 7 - An airship is to operate at 20 m/s in air at...Ch. 7 - An airplane wing of 3 m chord length moves through...Ch. 7 - A flat plate 1.5 m long and 0.3 m wide is towed at...Ch. 7 - This 1:12 pump model using water at 15C simulates...Ch. 7 - An ocean-going vessel is to be powered by a...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - A 1:3 scale model of a torpedo is tested in a wind...Ch. 7 - A flow rate of 0:18 m3/s of water at 20C...Ch. 7 - A force of 9 N is required to tow a 1:50 ship...Ch. 7 - An airplane wing, with chord length of 1.5 m and...Ch. 7 - A water pump with impeller diameter of 24 in. is...Ch. 7 - A model hydrofoil is to be tested at 1:20 scale....Ch. 7 - A ship 120 m long moves through freshwater at 15C...Ch. 7 - A 1:30 scale model of a cavitating overflow...Ch. 7 - In some speed ranges, vortices are shed from the...Ch. 7 - A 1:8 scale model of a tractor-trailer rig is...Ch. 7 - On a cruise ship, passengers complain about the...Ch. 7 - When a sphere of 0.25 mm diameter and specific...Ch. 7 - The flow about a 150 mm artillery projectile which...Ch. 7 - Your favorite professor likes mountain climbing,...Ch. 7 - A 1:50-scale model of a submarine is to be tested...Ch. 7 - Consider water flow around a circular cylinder, of...Ch. 7 - A 1:10 scale model of a tractor-trailer rig is...Ch. 7 - The power, P, required to drive a fan is assumed...Ch. 7 - Over a certain range of air speeds, V, the lift,...Ch. 7 - The pressure rise, p, of a liquid flowing steadily...Ch. 7 - An axial-flow pump is required to deliver 0.75...Ch. 7 - A model propeller 1 m in diameter is tested in a...Ch. 7 - Consider Problem 7.38. Experience shows that for...Ch. 7 - Closed-circuit wind tunnels can produce higher...Ch. 7 - A 1:16 model of a bus is tested in a wind tunnel...Ch. 7 - The propagation speed of small-amplitude surface...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
ICA 8-51
The thermal conductivity of a plastic is 0.325 British thermal units per foot hour degree Fahrenheit [...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Calculate the metal removal rate for machining at a speed of 80 fpm, feed of 0.030 ipr, at a depth of 0.625 in....
Degarmo's Materials And Processes In Manufacturing
The required electric power for annealing.
Introduction to Heat Transfer
Determine the reactions at the fixed support A and the roller B. EI is constant.
Mechanics of Materials (10th Edition)
Hoover Dam across the Colorado River dams up Lake Mead 200m higher than the river downstream (see Fig. P4.31). ...
Fundamentals Of Thermodynamics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.arrow_forwardThis pleasearrow_forwardI need help figuring out this question, I'm at a loss (step by step helps too):arrow_forward
- The true optionarrow_forward1. The thrust of a marine propeller Fr depends on water density p, propeller diameter D, speed of advance through the water V, acceleration due to gravity g, the angular speed of the propeller w, the water pressure p, and the water viscosity μ. You want to find a set of dimensionless variables on which the thrust coefficient depends. In other words CT = FT · = ƒen(#1, #2, ...) pV2D2 (a) What is k? Explain. (b) Find the 's on the right-hand-side of equation 1 if one of them HAS to be a Froude number gD/V², (1)arrow_forwardPravinbhaiarrow_forward
- A 1:7 scale model simulates the operation of a large turbine that is to generate200 kW with a flow rate of 1.5 m3/s. What flow rate should be used in the model, andwhat power output is expected?(a) Water at the same temperature is used in both model and prototype.(b) The model water is at 25°C and the prototype water is at 10°C.arrow_forwardWhen a capillary tube of small diameter D is inserted into a container of liquid, the liquid rises to height h inside the tube (Fig.). h is a function of liquid density ? , tube diameter D, gravitational constant g, contact angle ?, and the surface tension ?s of the liquid. (a) Generate a dimensionless relationship for h as a function of the given parameters. (b) Compare your result to the exact analytical equation for h. Are your dimensional analysis results consistent with the exact equation? Discuss.arrow_forwardFluid Mechanicsarrow_forward
- For a certain fluid-flow problem it is known that both the Froude number and the Weber number are important dimensionless parameters. If the problem is to be studied by using a 1:10 scale model, determine the required surface tension scale if the density scale is equal to 1. The model and prototype operate in the same gravitational field. 0m/0= iarrow_forwardA ship 350 m long moves in sea water whose density is 1030 kg/m3 . A 1:120 model of this ship is to be tested in a wind tunnel. The velocity of the wind tunnel around the model is 35 m/s and the resistance of the model is 65 N. Determine the velocity and also the resistance of the ship in sea water. The density of air is given as 1.24 kg/m3 . Take the kinematic viscosity of air and sea water as 0.012 stokes and 0.018 stokes respectively.arrow_forwardA ship 350 m long moves in sea water whose density is 1030 kg/m3 . A 1:120 model of this ship is to be tested in a wind tunnel. The velocity of the wind tunnel around the model is 35 m/s and the resistance of the model is 65 N. Determine the velocity and also the resistance of the ship in sea water. The density of air is given as 1.24 kg/m3 . Take the kinematic viscosity of air and sea water as 0.012 stokes and 0.018 stokes respectively.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license