Concept explainers
Experiments show that the pressure drop for flow through an orifice plate of diameter d mounted in a length of pipe of diameter D may be expressed as
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Heating Ventilating and Air Conditioning: Analysis and Design
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Mechanics of Materials (10th Edition)
Introduction to Heat Transfer
- This pleasearrow_forwardUsing dimensional analysis, show thatarrow_forwardWhen fluid in a pipe is accelerated linearly from rest, itbegins as laminar flow and then undergoes transition toturbulence at a time t tr that depends on the pipe diameterD , fluid acceleration a , density ρ , and viscosity μ .Arrange this into a dimensionless relation between t trand D .arrow_forward
- The pressure drop (Ap) test is carried out using a pipe configuration as illustrated below: Manometer 1 Manometer 2 straight pipe D= 2R R= radius in pipe The pipe data and the flowing fluid are as follows: Pipe: D = 1 cm; L= 100 cm. Fluid: Water, with density (A) = 1000 kg/m"; absolute viscosity (u) = 0.001 kg/im.s); Experimental data is shown as shown in the following table: Task: Ja. Plot the graph of the pressure as a function of the average velocity (V.v). b. Based on the equation for laminar flow in the pipe as follows: Ap = 32VuL, Vavg (m/s) Ap (Pa) 0,001 0,002 0,005 0,01 0,02 0,04 0,06 0,08 0,1 0,12 0,15 0,30 0,62 1,61 3,10 6,10 12,10 20,10 26,00 32,50 38,90 47,20 D Compare the experimental results in the table with the results of calculations using the above equation. Leave a comment. Note: Ap = p1-p2. c. The coefficient of friction (f) in the pipe is formulated as follows: f- 2DAD PL(V.) plot (plot) this distribution of fas a function of the Reynolds number (Re). Re is…arrow_forwardIn falling ball viscometer experiment, the viscometer with a calibration factor K=0.3 is used to measure the viscosity of oil with density p3D 0.8 gr/cm and the density of Tantalum ball is 16.6 gr/cm, if the ball is observed to fall 250 mm in time 50.3 sec. What is the viscosity of the oil (in cp)?arrow_forwardIn the orifice and Jet flow experiment, the following data were collected: Water level = 30 cm , Volume V {V} L was collected in time 32 seconds, orifice diameter = 6 mm, X1 = 50 mm , X2 = 100 mm, X3 = 150 mm, X4 = 200 mm, X5 = 250 mm Y1 = 3 mm, Y2 = 10 mm, Y3 = 22 mm, Y4 = 38 mm, Y5 = 63 mm What is the actual velocity of water jet that leaves the orifice (m/s)?arrow_forward
- Consider steady viscous flow through a small horizontal tube. For this type of flow, the pressure gradient along the tube, Δp ⁄ ΔL should be a function of the viscosity Y, the mean velocity V, and the diameter D. By dimensional analysis, derive a func- tional relationship relating these variables. Fluid mechanicsarrow_forwardHurry up plzarrow_forwardFluid Mechanics Laboratory (a report on this experiment is required) Experiment No.1 Reynolds number *data ? Please explain the calculation procedure step by steparrow_forward
- fluid mechanics experts please solve with details and give reasons for steps if needed. parts a b and c are solved . in this question i want the last two questions. please use the P that isobtained from g part in h part with P0 as example. σxx= -P + τxx = 0.125 ρ - P0 + 2μ = 0.75 Paarrow_forwardQ1: If an air stream flowing at velocity (U) pasta body of length (L) causes a drag force (F) on the body which depends only upon U, L, and fluid viscosity μ. Formulate the suitable dimensionless parameter of the air drag force.arrow_forwardA ship 350 m long moves in sea water whose density is 1030 kg/m3 . A 1:120 model of this ship is to be tested in a wind tunnel. The velocity of the wind tunnel around the model is 35 m/s and the resistance of the model is 65 N. Determine the velocity and also the resistance of the ship in sea water. The density of air is given as 1.24 kg/m3 . Take the kinematic viscosity of air and sea water as 0.012 stokes and 0.018 stokes respectively.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY