Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 22, Problem 17QLP
Which tool-material properties are suitable for interrupted cutting operations? Why?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Identify the forces involved in a cutting operation. which of these forces contributes to the power required?
In addition to cutting speed, what other cutting variables are included in the expanded version of the Taylor tool life equation?
Discuss the effects of cutting speed, feed rate, and depth of cut on the tool wear rate during a turning operation.
How does each parameter influence the surface finish of the workpiece?
Provide a detailed explanation based on the principles of metal cutting mechanics.
Chapter 22 Solutions
Manufacturing Engineering & Technology
Ch. 22 - What are the major properties required of...Ch. 22 - What is the composition of a typical carbide tool?Ch. 22 - Why were cutting-tool inserts developed?Ch. 22 - Why are some tools coated? What are the common...Ch. 22 - Explain the applications and limitations of...Ch. 22 - List the major functions of cutting fluids.Ch. 22 - Why is toughness important for cutting-tool...Ch. 22 - Is the elastic modulus important for cutting-tool...Ch. 22 - Explain how cutting fluids penetrate the toolchip...Ch. 22 - List the methods by which cutting fluids are...
Ch. 22 - Describe the advantages and limitations of (a)...Ch. 22 - What is a cermet? What are its advantages?Ch. 22 - Explain the difference between M-series and...Ch. 22 - Why is cBN generally preferred over diamond for...Ch. 22 - What are the advantages to dry machining?Ch. 22 - Explain why so many different types of...Ch. 22 - Which tool-material properties are suitable for...Ch. 22 - Describe the reasons for and advantages of coating...Ch. 22 - Make a list of the alloying elements used in...Ch. 22 - As stated in Section 22.1, tool materials can have...Ch. 22 - Explain the economic impact of the trend shown in...Ch. 22 - Why does temperature have such an important effect...Ch. 22 - Ceramic and cermet cutting tools have certain...Ch. 22 - What precautions would you take in machining with...Ch. 22 - Can cutting fluids have any adverse effects in...Ch. 22 - Describe the trends you observe in Table 22.2.Ch. 22 - Why are chemical stability and inertness important...Ch. 22 - Titanium-nitride coatings on tools reduce the...Ch. 22 - Describe the necessary conditions for optimal...Ch. 22 - Negative rake angles generally are preferred for...Ch. 22 - Do you think that there is a relationship between...Ch. 22 - Make a survey of the technical literature, and...Ch. 22 - In Table 22.1, the last two properties listed...Ch. 22 - It has been stated that titanium-nitride coatings...Ch. 22 - Note in Fig. 22.1 that all tool materials,...Ch. 22 - Referring to Table 22.1, state which tool...Ch. 22 - Which of the properties listed in Table 22.1 is,...Ch. 22 - If a drill bit is intended only for woodworking...Ch. 22 - What are the consequences of a coating on a tool...Ch. 22 - Discuss the relative advantages and limitations of...Ch. 22 - Emulsion cutting fluids typically consist of 95%...Ch. 22 - List and explain the considerations involved in...Ch. 22 - Review the contents of Table 22.1. Plot several...Ch. 22 - Obtain data on the thermal properties of various...Ch. 22 - The first column in Table 22.2 shows 10 properties...Ch. 22 - Describe in detail your thoughts regarding the...Ch. 22 - One of the principal concerns with coolants is...Ch. 22 - How would you go about measuring the effectiveness...Ch. 22 - There are several types of cutting-tool materials...Ch. 22 - Assume that you are in charge of a laboratory for...Ch. 22 - Tool life could be greatly increased if an...Ch. 22 - List the concerns you would have if you needed to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Tool design What are some of the typical considerations for each one of the following metal cutting processes.arrow_forwardIn orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the main cutting force is 1000 N and the feed force is 800 N. The shear angle is 25° and orthogonal rake angle is zero Employing Merchant's theory, what is the ratio of friction force to normal force acting on the cutting tool?arrow_forward(b) During a certain machining experiment at the UCSI workshop, it is observed that temperature at the tool workpiece interface is 1200 °C at a cutting speed of 300 mm/min with a feed rate of 0.002 mm/rev. (1) Analyse how the temperature will be affected if the cutting speed is increased by 100 %. (ii) Detemine the cutting speed necessary to achieve a maximum cutting temperature of 900 °C.arrow_forward
- Question 2. The two sources of heat are (a) shearing in the primary shear plane and (b) friction at the tool-chip interface. What type of the tool wear or tool failure could be caused as a result of developing these heat sources on machining process? Explain your answer in accordance with following representation of tool wear. Insert cutting edgearrow_forward(b) A 400 mm long, 19.5 mm diameter of 304 stainless steel rod (assume specific energy of steel is 4 W.s/mm³) is being reduced in diameter to 17 mm by turning on a lathe machine. The spindle rotates at N = 700 rpm, and the tool is traveling at an axial speed of 300 mm/min. Calculate: (i) (ii) (iii) (iv) (v) cutting speed material removal rate cutting time power dissipated cutting forcearrow_forward8 - Orthogonal cutting is performed on a metal whose mass specific heat = 1.0 J/g-C, density 2.9 g/cm3, and thermal diffusivity = 0.8 cm2/s. The cutting speed is 4.5 m/s, uncut chip thickness (feed) is 0.25 mm, and width of cut (depth) is 2.2 mm. The cutting force is measured at 1170 N. Using Cook's equation, determine the cutting temperature. a) 417.09 b) O 707.60 C) 528.03 d) O 316.82 Boş bırakarrow_forward
- In an orthogonal cutting test with a bar of 75 mm diameter is reduced to 73 mm by using a HSS tool with arake angle = 10o, following observations were made: length of the chip, lc = 69.44 mm, cutting ratio r =0.3, the horizontal component of the cutting force, FH = 1450 N, and the vertical component of the cuttingforce, FV = 850 N. The various parameters recorded in this cutting operation are: depth of cut, d = 2 mm;feed rate, f = 0.3 mm/rev, cutting speed, V = 60 m/min. Using Merchant’s theory calculate the following:1) Friction force along rake face2) Normal force acting on rake face3) Shear force along the shear plane4) Normal force acting on shear plane5) The percentage error in shear angle predicted by Merchant’s theory6) Shear velocity7) Chip velocity8) Total work done9) The shear work proportion out of the total work done10) The friction work proportion out of the total work donearrow_forwardDuring orthogonal cutting operation of material has shear strength 95.5 Mpa. The cutting force is more than thrust force by 10%. The rake angle = 5°, the width of the cut = 5.0 mm, the chip thickness before the cut = 0.6, and the chip thickness ratio = 0.38. Determine (a) both cutting force and thrust force and (b) the coefficient of friction in the operation.arrow_forwardWhat are the types of cutting chip? How does the built-up-edge (BUE) form, and what are the influences of BUE on metal cutting?arrow_forward
- Choose TWO (2) types of cutting processes that are suitable for cutting thick materials (>20mm thick plate).arrow_forwardDefine specific energy for plane strain machining (cutting). In plane-strain machỉning, the two main sources of energy dissipation are deformation along the shear plane (~70%) and friction at the tool-chip contact along the rake face (~30%). Consider machining of a rigid perfectly-plastic work material whose uniaxial yield stress is 700 MPa, and is independent of strain rate and temperature. A tool of zero-degree rake angle is employed. Measurements showed the (deformed) chip thickness to be twice that of the undeformed chip thickness. Based on the aforementioned distribution of energy, estimate the specific energy for this process.arrow_forward(e) Briefly describe types of chips that occur in metal cutting. (f) For orthogonal cutting, the tool rake angle =15°. The chip thickness before the cut is 0.30mm and the cut yields a deformed chip thickness = 0.65mm. Calculate the shear plane angle and shear strain.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License