Explanation Given information: The time is 1 s , the mass of the capsule is 1000 kg , the radius of gyration in x axis is 1 m , the radius of gyration in y axis is 1 m , the radius of gyration in z axis is 1.25 m and the produced thrust is 50 N . Write the expression of angular momentum about point G . H G = I x ω x i + I y ω y j + I z ω z k ....... (I) Here, the moment of inertia about x axis is I x , the angular velocity in x direction is ω x , the unit vector in x direction is i , the moment of inertia about y axis is I y , the angular velocity in y direction is ω y , the unit vector in y direction is j , the moment of inertia about z axis is I z , the angular velocity in z direction is ω z , and the unit vector in z direction is k . Write the expression of angular momentum about the mass centre. H G = ( H G ) x i + ( H G ) y j + ( H G ) z k ....... (II) Here, the angular momentum along x axis is ( H G ) x , the angular momentum along y axis is ( H G ) y and the angular momentum along z axis is ( H G ) z . Write the expression moment about the mass centre. M G = r A / G × F A × Δ t i ....... (III) Here, the distance of A with respect to the mass centre is r A / G , the thrust is F A and the time period is Δ t . Write the expression of the distance of A with respect to the mass centre. r A / G = y 1 j + z 1 k ...... (IV) Here, the distance of A from y axis is y 1 and the distance from z axis is z 1 . Write the expression of principle of impulse and momentum. H G = M G ...... (V) The below figure represent the angular momentum. Figure-(1) Write the expression of angle of axis of precision as shown in Figure-1. tan θ = ( H G ) y ( H G ) z ...... (VI) Substitute ( H G ) x i + ( H G ) y j + ( H G ) z k for H G in Equation (I). ( H G ) x i + ( H G ) y j + ( H G ) z k = I x ω x i + I y ω y j + I z ω z k ...... (VII) Compare the unit vector i on both sides of Equation (IX). ( H G ) x = I x ω x ...... (VIII) Compare the unit vector j on both sides of Equation (IX). ( H G ) y = I y ω y ...... (IX) Compare the unit vector k on both sides of Equation (IX). ( H G ) k = I k ω k ....... (X) Write the expression of moment of inertia about x axis. I x = m k x 2 ....... (XI) Here, the radius of gyration in x direction is k x . Write the expression of moment of inertia about y axis. I y = m k y 2 ...... (XII) Here, the radius of gyration in x direction is k y 2 . Write the expression of moment of inertia about z axis. I z = m k z 2 ...... (XIII) Here, the radius of gyration in x direction is k z . Write the expression of resultant angular velocity. ω = ω x 2 + ω y 2 + ω z 2 ...... (XIV) The below figure represent the angular velocity component. Figure-(2) Write the expression of angle between angular velocity components as shown in Figure-(2). tan γ = ω y ω z ...... (XV) The below figure represent the diagram of rate of precision and spin. Figure-(3) Write the expression of lamis theorem applied on Figure-(3). ϕ ˙ sin γ = ψ ˙ sin ( γ − θ ) ϕ ˙ sin γ = ω sin θ ...... (XVI) Here, the rate of precision is ϕ ˙ and the rate of spin is ψ ˙ . Calculation: Substitute 2 m for y 1 and − 1.25 m for z 1 in Equation (IV). r A / G = ( 2 m ) j − ( 1.25 m ) k Substitute ( 2 m ) j − ( 1.25 m ) k for r A / G , 50 N for F A and 1 s for Δ t in Equation (III). M G = { ( 2 m ) j − ( 1.25 m ) k } × ( 50 N ) i × 1 s = { ( 2 m ) j − ( 1.25 m ) k } × ( 50 N ⋅ s ) i ...... (XVII) The Equation (IV) is a cross product of two vectors, now change Equation (XVIII) in determinant form. M G = | i j k 0 2 m − 1.25 m 50 N ⋅ s 0 0 | = ( 0 − 0 ) i − { 0 − ( − 62.5 N ⋅ m ⋅ s ) } j − { 0 − ( 100 N ⋅ m ⋅ s ) } k = − ( 62.5 N ⋅ m ⋅ s ) j − ( 100 N ⋅ m ⋅ s ) k ..... (XIX) Substitute − ( 62.5 N ⋅ m ⋅ s ) for ( H G ) y and − ( 100 N ⋅ m ⋅ s ) for ( H G ) z in Equation (VI). tan θ = − ( 62.5 N ⋅ m ⋅ s ) − ( 100 N ⋅ m ⋅ s ) tan θ = 62.5 100 θ = tan − 1 ( 0.32625 ) θ = 32 ° So, the axis of precision is at 32 ° . Substitute − ( 62.5 N ⋅ m ⋅ s ) j − ( 100 N ⋅ m ⋅ s ) k for M G and ( H G ) x i + ( H G ) y j + ( H G ) z k for H G in Equation (V)

12th Edition

ISBN: 9781259977237

Author: BEER

Publisher: MCG

See similar textbooks

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be create…

Videos

Question

Chapter 18, Problem 18.156RP

To determine

The axis of precision.

The rate of precision.

The rate of spin.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 18, Problem 18.155RP

Chapter 18, Problem 18.157RP

Students have asked these similar questions

Consider a piece of steel undergoing a decarburization process at 925 degrees C. the mass diffusivity of carbon in steel at 925 degrees C is 1*10^-7 cm^2/s. Determine the depth below the surface of the steel at which the concentration of carbon is reduced to 40 percent from its initial value as a result of the decarburization process for (a) an hour and (b) 10 hours. Assume the concnetration of carbon at the surface is zero throughout the decarburization process.

Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it carefully and give your own answer. You can borrow ideas from gpt, but please do not believe its answer.Very very grateful! Please do not copy other's work,i will be very very grateful!!

Multiple Choice Circle the best answer to each statement. 1. Which geometry attribute deviation(s) can be limited with a profile of a surface tolerance? A. Location B. Orientation C. Form D. All of the above 2. A true profile may be defined with: A. Basic radii B. Basic angles C. Formulas D. All of the above 3. Which modifier may be applied to the profile tolerance value? A B C. D. All of the above 4. The default tolerance zone for a profile tolerance is: A. Non-uniform B. Unilateral C. Bilateral equal distribution D. Bilateral-unequal distribution 5. An advantage of using a profile tolerance in place of a coordinate tolerance is: A. A bonus tolerance is permitted. B. A datum feature sequence may be specified C. A profile tolerance always controls size D. All of the above 6. The shape of the tolerance zone for a profile tolerance is: A. Two parallel planes B. The same as the true profile of the toleranced surface C. Equal bilateral D. Cylindrical when the diameter symbol is speci- fied…

Chapter 18 Solutions

Vector Mechanics For Engineers

Ch. 18.1 - Prob. 18.1P Ch. 18.1 - Prob. 18.2P Ch. 18.1 - Prob. 18.3P Ch. 18.1 - A homogeneous disk of weight W=6 lb rotates at the...Ch. 18.1 - Prob. 18.5P Ch. 18.1 - A solid rectangular parallelepiped of mass m has a...Ch. 18.1 - Solve Prob. 18.6, assuming that the solid...Ch. 18.1 - Prob. 18.8P Ch. 18.1 - Determine the angular momentum HD of the disk of...Ch. 18.1 - Prob. 18.10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The axis of precision. The rate of precision. The rate of spin.

Solution Summary: The author explains the axis of precision, the rate of spin, and the expression of angular momentum about point G.