
Concept explainers
A uniformly loaded square crate is released from rest with its comer D directly above A; it rotates about A until its comer B strikes the floor, and then rotates about B. The floor is sufficiently rough to prevent slipping and the impact at B is perfectly plastic. Denoting by

(a)
The angular velocity of the crate immediately after B strikes the floor.
Answer to Problem 17.118P
The angular velocity of the square box after striking B on the floor will be
Explanation of Solution
Given:
Square box which is uniformly loaded is released on the floor when its corner D is directly above the A. square box tends to rotate till it strikes the floor. The floor is made anti-slipping and impact at B is perfectly plastic.
Concept:
According to impulse momentum principle,
Calculation:
Let’s consider,
M = mass of a square box.
C = length of the side.
Moment of inertia =
We can say,
Taking moment at A,
Conclusion:
The angular velocity of the square box after striking B on the floor will be

(b)
The fraction of kinetic energy lost during the impact.
Answer to Problem 17.118P
The fractions of energy lost during impact conditions are.
Explanation of Solution
Given:
Square box which is uniformly loaded is released on the floor when its corner D is directly above the A. square box tends to rotate till it strikes the floor. The floor is made anti-slipping and impact at B is perfectly plastic.
Calculation:
Kinetic energy before impact,
Similarly kinetic energy after impact,
Combining E1 and E2 to find fraction of energy cost,
Conclusion:
The fraction of energy lost during impact conditions is

(c)
The angle through which the crater will rotate after B strikes the floor.
Answer to Problem 17.118P
Angle made by corner A of square box and floor will be 1.500
Explanation of Solution
Given:
Square box which is uniformly loaded is released on the floor when its corner D is directly above the A. square box tends to rotate till it strikes the floor. The floor is made anti-slipping and impact at B is perfectly plastic.
Concept:
As per law of conservation of energy before impact,
And that of after impact,
Before impact,
After impact,
As,
But
Therefore, from geometry,
Equating both equations of h3
Conclusion:
Want to see more full solutions like this?
Chapter 17 Solutions
Vector Mechanics For Engineers
- A 23-ft3 rigid tank initially contains saturated refrigerant-134a vapor at 160 psia. As a result of heat transfer from the refrigerant, the pressure drops to 50 psia. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the heat transfer. The heat transfer is Btu.arrow_forwardThe shaft shown in the figure below is subjected to axial loads as illustrated. The diameters of segments AB, BC, and CD are 20mm, 25mm, and 15mm, respectively. If the modulus of elasticity of the material is 610 MPa. Determine the change of A to D lengtharrow_forwardDetermine the final pressure and temperature. The final pressure is kPa. The final temperature is ºC.arrow_forward
- Air enters the 1-m2 inlet of an aircraft engine at 100 kPa and 20°C with a velocity of 184 m/s. Determine the volume flow rate, in m3/s, at the engine’s inlet and the mass flow rate, in kg/s, at the engine’s exit. The gas constant of air is R = 0.287 kPa·m3/kg·K. The volume flow rate at the engine’s inlet m3/s. The mass flow rate at the engine’s exit is kg/s.arrow_forwardThe ventilating fan of the bathroom of a building has a volume flow rate of 33 L/s and runs continuously. If the density of air inside is 1.20 kg/m3, determine the mass of air vented out in one day. The mass of air is kg.arrow_forwardA steady-flow compressor is used to compress helium from 15 psia and 70°F at the inlet to 200 psia and 600°F at the outlet. The outlet area and velocity are 0.01 ft2 and 100 ft/s, respectively, and the inlet velocity is 53 ft/s. Determine the mass flow rate and the inlet area. The gas constant of helium is R = 2.6809 psia·ft3/lbm·R. The mass flow rate is lbm/s. The inlet area is ft2.arrow_forward
- 1. The maximum and minimum stresses as well as the shear stress seen subjected the piece in plane A-A. Assume it is a cylinder with a diameter of 12.7mm 2. Draw the Mohr circle for the stress state using software. 3. Selection of the material for the prosthesis, which must be analyzed from the point of safety and cost view.arrow_forwardMarrow_forward× Your answer is incorrect. (Manometer) Determine the angle 0 of the inclined tube shown in figure below if the pressure at A is 1 psi greater than that at B. 1ft SG=0.61 十 A Ꮎ 1ft SG=1.0 8.8 ft 0 = Hi 15.20 deg Airarrow_forward
- I don't know how to solve thisarrow_forward1. The maximum and minimum stresses as well as the shear stress seen subjected the piece in plane A-A. Assume it is a cylinder with a diameter of 12.7mm 2. Draw the Mohr circle for the stress state using software. 3. Selection of the material for the prosthesis, which must be analyzed from the point of safety and cost view.arrow_forwardFirst, define the coordinate system XY with its origin at O2 and X-axis passing through O4 asshown above, then based on the provided steps Perform coordinate transformation from XY to xy to get the trajectory of point P. Show all the steps and calcualtionsarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





