(a) Explanation Calculation: The expression to determine the value of the low level of the input voltage is given by, V I L = V T N + V D D + V T P − V T N ( K n K p − 1 ) ( K n K p K n K p + 3 − 1 ) Substitute 50 μA / V 2 for K p , 100 μA / V 2 for K n , 0.35 V for V T N , − 0.35 V for V T P and 2.5 V for V D D in the above equation. V I L = 0.35 V + 2.5 V + ( − 0.35 V ) − 0.35 V ( 100 μA / V 2 50 μA / V 2 − 1 ) ( 100 μA / V 2 50 μA / V 2 100 μA / V 2 50 μA / V 2 + 3 − 1 ) = 0.82682 V The expression to determine the value of the high level of input voltage is given by, V I H = V T N + V D D + V T P − V T N ( K n K p − 1 ) ( 2 K n K p 3 K n K p + 1 − 1 ) Substitute 50 μA / V 2 for K p , 100 μA / V 2 for K n , 0.35 V for V T N , − 0.35 V for V T P and 2.5 V for V D D in the above equation. V I H = 0.35 V + 2.5 V + ( − 0.35 V ) − 0.35 V ( 100 μA / V 2 50 μA / V 2 − 1 ) ( 2 ( 100 μA / V 2 50 μA / V 2 ) 3 ( 100 μA / V 2 50 μA / V 2 ) + 1 − 1 ) = 1.2716 V The expression to determine the value of the high level of output voltage is given by, V O H U = 1 2 ( ( 1 + K n K p ) V I L + V D D − ( K n K p ) V T N − V T P ) Substitute 1 (b) To determine The noise margins.

MICROELECT. CIRCUIT ANALYSIS&DESIGN (LL)

4th Edition

ISBN: 9781266368622

Author: NEAMEN

Publisher: MCG

See similar textbooks

Videos

Question

Chapter 16, Problem 16.45P

(a)

To determine

The value of the input and the output voltage.

(b)

To determine

The noise margins.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 16, Problem 16.44P

Chapter 16, Problem 16.46P

Students have asked these similar questions

Please confirm that my solution is correct, especially the block diagram. Please DRAW (not type) what the block diagram would look like if it's incorrect. thank you

use this code on the bottom to answer the question in the photo clc; clearvars; % Read the file [y, Fs] = audioread('106miles.wav'); N = length(y); Nfft = 2^nextpow2(N); dt = 1/Fs; t = (0:dt:(N-1)*dt)'; % Ensure t is a column vector y = y - mean(y); % Remove DC component (if not already zero-mean) % Carrier signal (25 kHz) fc = 25000; % Carrier frequency in Hz carrier = cos(2 * pi * fc * t); % DSB-SC Modulation modulated_signal = y .* carrier; % Plot Time Domain Signal figure; subplot(2,1,1); plot(t, y); title('Original Signal (Time Domain)'); xlabel('Time (s)'); ylabel('Amplitude'); subplot(2,1,2); plot(t, modulated_signal); title('DSB-SC Modulated Signal (Time Domain)'); xlabel('Time (s)'); ylabel('Amplitude'); % Frequency Domain (FFT) Y = fft(y, Nfft) / Nfft; Modulated_Y = fft(modulated_signal, Nfft) / Nfft; f = Fs * (0:(Nfft/2)) / Nfft; % Frequency vector % Plot Frequency Domain Signal figure; subplot(2,1,1); plot(f, abs(Y(1:Nfft/2+1))); title('Original Signal…

5-9 A 230 V shunt motor has a nominal arma- ture current of 60 A. If the armature resist- ance is 0.152, calculate the following: a. The counter-emf [V] b. The power supplied to the armature [W] c. The mechanical power developed by the motor, [kW] and [hp] 5-10 a. In Problem 5-9 calculate the initial start- ing current if the motor is directly con- nected across the 230 V line. b. Calculate the value of the starting resistor needed to limit the initial current to 115 A.

Chapter 16 Solutions

MICROELECT. CIRCUIT ANALYSIS&DESIGN (LL)

Ch. 16 - Consider the NMOS inverter with resistor load in...Ch. 16 - The enhancementload NMOS inverter in Figure...Ch. 16 - Prob. 16.3EP Ch. 16 - Prob. 16.4EP Ch. 16 - Consider the NMOS inverter with enhancement load,...Ch. 16 - Prob. 16.2TYU Ch. 16 - (a) Consider the results of Exercise Ex 16.1....Ch. 16 - Prob. 16.5EP Ch. 16 - Prob. 16.6EP Ch. 16 - (a) Design a threeinput NMOS NOR Logic gate with...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

The value of the input and the output voltage.

Solution Summary: The author explains the value of the input and output voltage. The expression to determine the low level of input voltage is given by c

Videos

The value of the input and the output voltage.

The noise margins.

Want to see the full answer?

Chapter 16 Solutions