The correct IUPAC name for the given compound has to be chosen from the given options. Concept Introduction: IUPAC nomenclature for alkene : There are about eight rules to be followed in giving IUPAC name for alkene. The suffix –ane has to be replaced with the suffix –ene. This is used to indicate the presence of double bond. The longest continuous chain of carbon atoms has to be chosen that contains both carbon atoms of the double bond. The parent carbon chain has to be numbered in a way so that the numbering begins at the end near to the double bond. In case if the double bond is equidistant from both ends, then numbering has to be done from the end that is closer to substituents. The position of the double bond has to be given a single number which is lower‑numbered carbon atom that is present in the double bond. Suffixes like –diene, -triene, -tetrene, and so on are used when the compound contains more than one double bond. In case of cycloalkenes which do not have any substitution, the numbering is not needed to locate the double bond because the bond is assumed to be between the carbons 1 and 2. In case if substituents are present in cycloalkene, then the double‑bonded carbon atoms are numbered 1 and 2 in a direction where the substituent gets the lower number. If the cycloalkenes contain more than one double bond, then one double bond is assigned the numbers 1 and 2 followed by the other double bond so that the lowest number possible is given. Structural formula where a line represent carbon‑carbon bond and the carbon atom is considered to be present in each point and the end of lines is known as Line-angle structural formula. To indicate a double bond between carbon atom, double line is used.

Question

Want to see the full answer?

Answer 1

Question

Chapter 13.4, Problem 1QQ

Interpretation Introduction

Interpretation:

The correct IUPAC name for the given compound has to be chosen from the given options.

Concept Introduction:

IUPAC nomenclature for alkene: There are about eight rules to be followed in giving IUPAC name for alkene.

The suffix –ane has to be replaced with the suffix –ene. This is used to indicate the presence of double bond.

The longest continuous chain of carbon atoms has to be chosen that contains both carbon atoms of the double bond.

The parent carbon chain has to be numbered in a way so that the numbering begins at the end near to the double bond. In case if the double bond is equidistant from both ends, then numbering has to be done from the end that is closer to substituents.

The position of the double bond has to be given a single number which is lower‑numbered carbon atom that is present in the double bond.

Suffixes like –diene, -triene, -tetrene, and so on are used when the compound contains more than one double bond.

In case of cycloalkenes which do not have any substitution, the numbering is not needed to locate the double bond because the bond is assumed to be between the carbons 1 and 2.

In case if substituents are present in cycloalkene, then the double‑bonded carbon atoms are numbered 1 and 2 in a direction where the substituent gets the lower number.

If the cycloalkenes contain more than one double bond, then one double bond is assigned the numbers 1 and 2 followed by the other double bond so that the lowest number possible is given.

Structural formula where a line represent carbon‑carbon bond and the carbon atom is considered to be present in each point and the end of lines is known as Line-angle structural formula. To indicate a double bond between carbon atom, double line is used.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Part VII. The H-NMR of a compound with molecular formula C5 H 10 O2 is given below. Find the following: (a) The no. of protons corresponding to each signal in the spectra (6) Give the structure of the compound and assign the signals to each proton in the compound. a 70.2 Integration Values C5H10O2 b 47.7 C 46.5 d 69.5 3.6 3.5 3.4 3.3 3.2 3.1 3.0 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2.0 Chemical Shift (ppm) 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8

Part 111. 1 H-NMR spectrum of a compound with integration values in red is given below. Answer the following: (a) write the signals in the 'H-NMR spectrum to the corresponding protons on the structure of the molecule below. (b) Identify the theoretical multiplicities for each proton in the compound. Also give the possible. complex splitting patterns assuming J values are not similar. там Br 22 2 3 6 4 7.2 7.0 6.8 6.6 6.4 6.2 6.0 5.8 5.6 5.4 5.2 5.0 4.8 4.6 4.4 4.2 4.0 3.8 3.6 3.4 3.2 3.0 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0 Chemical Shift (ppm) ra. Br 2 3 6 6 2.5 2.4 2.3 2.2 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 Chemical Shift (ppm) 2 2 Br 7.3 7.2 7.1 7.0 6.9 6.7 6.6 6.5 6.4 6.3 6.2 6.1 6.0 Chemical Shift (ppm) 5.9 5.8 5.7 5.5 5.4 5.3 5.2 5.0 4.9

1600° 1538°C 1493°C In the diagram, the letter L indicates that it is a liquid. Indicate its components in the upper region where only L is indicated. The iron-iron carbide phase diagram. Temperature (°C) 1400 8 1394°C y+L 1200 2.14 y, Austenite 10000 912°C 800a 0.76 0.022 600 400 (Fe) a, Ferrite Composition (at% C) 15 1147°C a + Fe3C 2 3 Composition (wt% C) L 2500 4.30 2000 y + Fe3C 727°C 1500 Cementite (Fe3C) 1000 4 5 6 6.70 Temperature (°F)