Degarmo's Materials And Processes In Manufacturing

13th Edition

ISBN: 9781119492825

Author: Black, J. Temple, Kohser, Ronald A., Author.

Publisher: Wiley,

See similar textbooks

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condit…

Videos

Textbook Question

Chapter 13, Problem 34RQ

What is fluidity, and how can it be measured?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 13, Problem 33RQ

Chapter 13, Problem 35RQ

Students have asked these similar questions

Question 2 A component is sand casted in pure aluminum. The level of the metal inside a pouring basin is 215 mm above the level of the metal in the mould. For a viscosity value of 0.0017 Ns/m² and a circular runner with a diameter of 11 mm, calculate: The velocity and rate of flow of the metal into the mould. What effect does turbulent flow in a gating system have on the casting? 2.3 Which measures can be implemented to reduce turbulent flow?

Q.Define the slip and show the effect of slip on velocity ratio.

What are limits or limits of size?

Chapter 13 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 13 - What are the six activities that are conducted on...Ch. 13 - What is materials processing?Ch. 13 - What are the five basic families of...Ch. 13 - Describe the capabilities of the casting process...Ch. 13 - What are some of the various mold materials and...Ch. 13 - How might the desired production quantity...Ch. 13 - Why is it important to provide a means of venting...Ch. 13 - What types of problem or defect can occur if the...Ch. 13 - Why might product removal be less of a problem...Ch. 13 - What is a casting pattern? Flask? Core? Mold...

Ch. 13 - In a horizontally parted two-part mold, what is...Ch. 13 - What are some of the components that combine to...Ch. 13 - What is a parting line or parting surface?Ch. 13 - What is draft, and why is it used?Ch. 13 - Why is it important to control the solidification...Ch. 13 - What are the two stages of solidification, and...Ch. 13 - Why is it that most solidification does not begin...Ch. 13 - Why might it be desirable to promote nucleation in...Ch. 13 - Nucleation generally begins at preferred sites...Ch. 13 - Why might directional solidification be desirable...Ch. 13 - Describe some of the key features observed in the...Ch. 13 - What is superheat?Ch. 13 - Prob. 23RQ Ch. 13 - What is a liquidus temperature? A solidus...Ch. 13 - What is the freezing range for a metal or alloy?Ch. 13 - Discuss the roles of casting volume and surface...Ch. 13 - What characteristics of a specific casting process...Ch. 13 - What is the correlation between cooling rate and...Ch. 13 - What is the chill zone of a casting, and why does...Ch. 13 - Which of the three regions of a cast structure is...Ch. 13 - What is dross or slag, and how can it be prevented...Ch. 13 - What are some of the possible approaches that can...Ch. 13 - What is a misrun or cold shut, and what causes...Ch. 13 - What is fluidity, and how can it be measured?Ch. 13 - What is the most important factor controlling the...Ch. 13 - What defect can form in sand castings if the...Ch. 13 - Why is it important to design the geometry of the...Ch. 13 - Why might it be preferable to attach gates to the...Ch. 13 - Prob. 39RQ Ch. 13 - What are some desirable features in the sprue...Ch. 13 - What is a choke, and how does its placement affect...Ch. 13 - What features can be incorporated into the gating...Ch. 13 - What are some of the materials and designs of...Ch. 13 - What factors might influence the positioning of...Ch. 13 - What features of the metal being cast tend to...Ch. 13 - What are the three stages of contraction or...Ch. 13 - Why is it more difficult to prevent shrinkage...Ch. 13 - What steps can be taken to compensate for the...Ch. 13 - During what stage of shrinkage might hot tears...Ch. 13 - What is the role of a riser?Ch. 13 - Why is it desirable to design a casting to have...Ch. 13 - What is yield, and how does it relate to the...Ch. 13 - Based on Chvorinovs rule, what would be an ideal...Ch. 13 - Define the following riser-related terms: top...Ch. 13 - What assumptions were made when using Chvorinovs...Ch. 13 - Discuss aspects relating to the connection between...Ch. 13 - What is the purpose of a chill? Of an insulating...Ch. 13 - What are some materials that are commonly used to...Ch. 13 - What types of modifications or allowances are...Ch. 13 - Prob. 60RQ Ch. 13 - What is the purpose of a draft or taper on pattern...Ch. 13 - Why is it desirable to make the pattern allowances...Ch. 13 - What additional adjustment or correction must be...Ch. 13 - What are some of the features of the casting...Ch. 13 - Prob. 65RQ Ch. 13 - What are some design recommendations for inside...Ch. 13 - What are some appearance considerations in parting...Ch. 13 - Prob. 68RQ Ch. 13 - Prob. 69RQ Ch. 13 - Using Chvorinovs rule as presented in the text...Ch. 13 - Reposition the riser in Problem 1 so that it sits...Ch. 13 - A rectangular casting having the dimensions 3 in....Ch. 13 - A cylinder with a diameter of 2.5 in. and a height...Ch. 13 - Figure 13.Ashows the wall profile of a cast iron...Ch. 13 - Investigate various experimental techniques to...Ch. 13 - Porosity within a casting can be either...Ch. 13 - The chapter text describes various materials that...Ch. 13 - What is the most likely source of the gas bubbles?...Ch. 13 - What factors may have caused the penetration...Ch. 13 - Prob. 3CS Ch. 13 - Prob. 4CS Ch. 13 - Prob. 5CS

Additional Engineering Textbook Solutions

Find more solutions based on key concepts

Summarize the steps involved when the Vole performs an instruction with op-code 0xB. Express your answer as a s...

Computer Science: An Overview (13th Edition) (What's New in Computer Science)

The switch shown in Fig. P 7.4 has been open for a long time before closing at t = 0. Figure P7.4 Find io(0−),...

Electric Circuits. (11th Edition)

In Exercises 1 through 52, determine the output produced by the lines of code. DimlastName,message,firstNameAsS...

Introduction To Programming Using Visual Basic (11th Edition)

Describe the common components needed to create a Web-based application.

Modern Database Management

Can a derived class directly access by name a private instance variable of the base class?

Java: An Introduction to Problem Solving and Programming (8th Edition)

1‘21 Same as Problem 1.20, excepi the anicle should be on safety as related to su rveying-

Elementary Surveying: An Introduction To Geomatics (15th Edition)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.