Concept explainers
Mountain Climbing. Mountaineers often use a rope to lower themselves down the face of a cliff (this is called rapelling). They do this with their body nearly horizontal and their feet pushing against the cliff (Fig. P11.45). Suppose that an 82.0-kg climber, who is 1.90 m tall and has a center of gravity 1.1 m from his feet, rappels down a vertical cliff with his body raised 35.0° above the horizontal. He holds the rope 1.40 m from his feet, and it makes a 25.0° angle with the cliff face. (a) What tension does his rope need to support? (b) Find the horizontal and vertical components of the force that the cliff face exerts on the climber’s feet. (c) What minimum coefficient of static friction is needed to prevent the climber’s feet from slipping on the cliff face if he has one foot at a time against the cliff?
Learn your wayIncludes step-by-step video
Chapter 11 Solutions
UNIVERSITY PHYSICS UCI PKG
Additional Science Textbook Solutions
Essential University Physics (3rd Edition)
An Introduction to Thermal Physics
College Physics
Conceptual Physical Science (6th Edition)
Life in the Universe (4th Edition)
Lecture- Tutorials for Introductory Astronomy
- A tire, which is mounted on a car, has a radius of 0.23m0.23m. A nail with a mass of 11.4g11.4g is stuck in the tread of the tire, and it is held there with a maximum frictional force of 0.53N0.53N. The car has been elevated on a mechanic lift so that the tire is no longer in contact with the pavement. Part (a) What is the tire tread’s lowest tangential speed, in meters per second, at which the nail will pull free from the tire? (How does gravity affect the net force on the nail at various positions in the rotation of the tire.) Part (b) At what tangential speed, in meters per second, would the nail pull free when it is at the top of the tire? (This is a mildly silly question because the nail would have already pulled free at some other point in the rotation.)arrow_forwardA circular plate with radius r = 0.941 m lies next to a rectangular plate with base br = 0.783 m and height hr = 0.898 m which lies next to a triangular, isosceles plate with base bt = 1.51 m and height ht = 0.80 m, see figure. Determine the common center of gravity of the three plates in the x-direction if the plates are the same thickness and are made of the same material.arrow_forwardLana Kane, Archer’s spy companion, is a 70 kg pole-vaulter. She falls from a peak height of 5.90 m after pole-vaulting over a crossbar set at that height. She lands on a thick mat. When Lana first makes contact with the mat, her center of gravity is only 1.0 m high. During her impact with the mat, the mat compresses. At the point of maximum compression, Lana’s vertical velocity reaches zero, and her center of gravity if only 0.5 m high. What average force did the mat exert on Lana during this impact?arrow_forward
- A 72.0-kg weightlifter doing arm raises holds a 7.50-kg weight. Her arm pivots around the elbow joint, starting 40.0° below the horizontal (Fig. P11.54). Biometric measurements have shown that, together, the forearms and the hands account for 6.00% of a person’s weight. Since the upper arm is held vertically, the biceps muscle always acts verti-cally and is attached to the bones of the forearm 5.50 cm from the elbow joint. The center of mass of this person’s forearm–hand combination is 16.0 cm from the elbow joint, along the bones of the forearm, and she holds the weight 38.0 cm from her elbow joint. (a) Draw a free-body diagram of the forearm. (b) What force does the biceps muscle exert on the forearm? (c) Find the magni-tude and direction of the force that the elbow joint exerts on the forearm. (d) As the weightlifter raises her arm toward a horizontal position, will the force in the biceps muscle increase, decrease, or stay the same? Why? Solve A B C D and show complete solutionarrow_forwardWe can model a pine tree in the forest as having a compact canopy at the top of a relatively bare trunk. Wind blowing on the top of the tree exerts a horizontal force, and thus a torque that can topple the tree if there is no opposing torque. Suppose a tree's canopy presents an area of 9.0 m2m2 to the wind centered at a height of 7.0 mm above the ground. (These are reasonable values for forest trees. *Part A If the wind blows at 6.5 m/sm/s, what is the magnitude of the drag force of the wind on the canopy? Assume a drag coefficient of 0.50 and the density of air of 1.2 kg/m3kg/m3. Express your answer with the appropriate units. *Part B What torque does this force exert on the tree, measured about the point where the trunk meets the ground? Express your answer with the appropriate units.arrow_forwardThe 77.0 kg painter in the figure below is using a large stepladder. The base of the ladder is 3.0 m wide, and the ladder is 7.0 m high. The painter is on a step that is 2.0 m above the floor. The horizontal bar of the ladder has a mass of 10.0 kg, and the entire ladder has a mass of 64.0 kg. Assume that the floor is frictionless. A В C 7.0 m 5.0 m 2.0 m 3.0 m (a) Find the force of tension in the horizontal bar and the normal forces that the floor exerts on the ladder. T = Number N Njeft = Number N Nright = Number (b) Find the action-reaction forces at the hinges A, B, and C. Enter each answer as the magnitude of the component of the hinge forces. Consider the positive r-direction to be rightwards and the positive y-direction to be upwards.arrow_forward
- An 85 kg window cleaner uses a 10 kg ladder that is 5.3 m long. He places one end on the ground 3.2 m from a wall, rests the upper end against a cracked window, and climbs the ladder. He is 1.6 m up along the ladder when the window breaks. Neglect friction between the ladder and window and assume that the base of the ladder does not slip. When the window is on the verge of breaking, what are (a) the magnitude of the force on the window from the ladder, (b) the magnitude of the force on the ladder from the ground, and (c) the angle (relative to the horizontal) of that force on the ladder?arrow_forwardThe 465-kg uniform I-beam supports the load shown. Determine the reactions at the supports. Answers: Ax= Ay= By= i -5.9 m- 3.1 m 200 kg zzzarrow_forwardJohn is performing an isometric contraction of the quadriceps to hold a 500 N weight at an angle of 45° of knee extension (i.e., 45° below the horizontal). Assume the length of the lower leg is 42.5 cm. How much force must the quadriceps produce if the moment arm for the patellar tendon is 10 mm?arrow_forward
- A ladder whose length L is 12m and whose mass m is 45kg rests against a wall. Its upper end is a distance h of 9.3m above the ground. The center of gravity of the ladder is one-third of the way up the ladder. A firefighter whose mass M is 72kg climbs halfway up to the ladder. Assume that the wall, but not the ground is frictionless. What forces are exerted on the ladder by the wall and by the ground?arrow_forwardThe femur of a human leg (mass 10 kg, length 0.9 m) is in traction, as shown in the figure. The center of gravity of the leg is one-third of the distance from the pelvis to the bottom of the foot. Two objects, with masses mj and m2, m, are hung at the ends of the leg using pulleys to provide upward support. A third object of 8 kg is hung to provide tension along the leg. The body provides tension as well. body Write a mathematical relationship relating mi to m2 in terms of m2 and numerical coefficients. 8 kg mj = m- m2 Incorrect Is the expression for m1 valid for more than one pair of values of mj and m2? yes no Incorrect Suppose the tension force due to mj is now applied at the leg's center of mass. Write a new expression relating m, to m2 in terms of m2, numerical coefficients, and given values. If you use a given value in your equation, enter it as a number without units.arrow_forward?arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning