Q4- A single phase transformer has 350 primary and secondary 1050 turns. The primary is connectedto 400 V,50 Hz a.c. supply. If the net cross sectional area of core is 50 cm2, calculate i) Themaximum value of the flux density in the core. ii) The induced e.m.f in the secondary winding. Ans:1.029 T, 1200V

Formulas to Use:1.Flux and Flux Linkage: The voltage equation for the transformer…

Answered: Q4- A single phase transformer has 350…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
An ideal transformer has no real or reactive power loss. (a) True (b) False
A single pahse transformer has 700 primary and 2100 secondary turns. The primary is connected to 400 V, 50 a.c. supply. If the net cross core is 100 cm². Calculate the maximum flux density in the core and induced e.m.f. in the secondary winding.
A single phase transformer has 350 primary and socondray 1050 turns. The primary is connected to 400 V ,50 Hz a.c. supply. If the net cross sectional area of core is 50 cm , calculate i) The maximum value of the flux density in the core. ii) The induced e.m.f in the secondary winding. Ans: 1.029 T ,1200v
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
A single phase 60 Hz transformer has its core volume of 1.5x10-3 cu m. The maximum flux density is 1.0 tesla and the hysteresis constant of the core is 6000. find the hysteresis loss.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
A single pahse transformer has 230 primary and 870 secondary turns. The primary is connected to 400 V, 50 Hz a.c. supply. If the net cross core is 50 cm². Calculate the maximum flux density in the core and induced e.m.f. in the secondary winding.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
1. In a transformer, which options are correct:A. Works on Faraday’ law and Ampere’s lawB. DC current in the primary winding will produce voltage output in the secondary windingC. Copper losses are caused by reluctance in magnetic circuitD. Frequency of input power source will not govern the voltage induced in secondary circuit.2. Voltage ratio of input voltage and output voltage in IDEAL transformer depends on:A. Leakage fluxB. Magnetization currentC. Copper loss currentD. Turns ratio3. The core of transformer must have:

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning