For the power system given below, the voltage at bus 2 is kept at 1.03 pu. The maximum power can be delivered by G2 is 35MW. Obtain the load flow solution. Take the base power 100 MVA.V₁ = 1.0520G₁0.02+j0.06G2 V2=1.03P2 = 35 MW0.08+j0.24SL2 20+j50 MVASL360+j25 MVA0.06+j0.018

Step 1: Given DataSlack Bus (Bus 1): V1=1.05∠0∘ (Voltage given, reference bus)PV Bus (Bus…

Answered: For the power system given below, the…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Find P5 and P100
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
An ac resistance is higher than a dc resistance. True False
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Identify the characteristics of AC and DC voltage. Runs at a higher temperature Answer 1Choose...DCAC More dangerous to transfer Answer 2Choose...DCAC Easy to produce Answer 3Choose...DCAC Easier to transform voltages Answer 4Choose...DCAC Voltage remains at a constant value Answer 5Choose...DCAC Cheaper to produce
Q20. The section bus-bars A and B as shown in Figure B5 are linked by a bus-bar reactors each rated at 5000 kVA with 10% reactance. On bus-bar A, there are two generators each of 10,000 kVA with 10% reactance and on B two generators each of 8000 kVA with 12 % reactance. Find the Current and MVA that fed into a dead short circuit between all phases on B with bus-bar reactor in the circuit. Page 4 of 5 جامعة التقنية والعلومر التطبيقية بإبراء University of Technology and Applied Sciences - Ibra Student ID: Section: Student Name: 8,000 kVA 12% 10,000 kVA 10,000 kVA 10% 8,000 kVA 12% 10% 2 3 5,000 kVA 10% lell 8,000 kVA 10% Figure B5 "End of Question Paper"
Three loads are connected in parallel across a 1400-V rms, 60-Hz single-phase supply as shown in Figure 2.8. Load 1: Inductive load, 125 kVA at 0.28 power factor. Load 2: Capacitive load, 10 kW and 40 kvar. Load 3: Resistive load of 15 kW. 1400 V (a) Find the total kW, kvar, kVA, and the supply power factor. 1 12 (b) A capacitor of negligible resistance is connected in parallel with the above loads to improve the power factor to 0.8 lagging. Determine the kvar rating of this ca- pacitor and the capacitance in uF. 13 3
14. Determine all of the branch currents for the circuit shown in Figure 3.6.9 assuming E is a 1 volt RMS sine. Show all work problems
lo R1 CR2 V alx ........ Figure Q2(b) : Two Closed Loops Circuit (i) Explain the steps required in supermesh analysis for Figure Q2(b). (ii) Determine the mesh currents using the Kirchhoff's Current Law (KCL) and Kirchhoff's Voltage Law (KVL) for Figure Q2(b).
14. Determine all of the branch currents for the circuit shown in Figure 3.6.9 assuming E is a 1 volt RMS sine. I want show all work problems step by step please correctly

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

For the power system given below, the voltage at bus 2 is kept at 1.03 pu. The maximum power can be delivered by G2 is 35 MW. Obtain the load flow solution. Take the base power 100 MVA. V₁ = 1.0520 G₁ 0.02+j0.06 G2 V2=1.03 P2 = 35 MW 0.08+j0.24 SL2 20+j50 MVA SL3 60+j25 MVA 0.06+j0.018