28. The minimum size raceway for the following conductors is: a. Three, 250 kcmil conductors with XHHW insulation b. One, 3⁄0 AWG conductor with XHHW insulation c. One, 4 AWG conductor with XHHW insulation29. The minimum size raceway for the following conductors is: a. Twelve, 6 AWG conductors with THHN insulation b. Nine, 8 AWG conductors with THHN insulation c. Eighteen, 10 AWG conductor with THHN insulation d. One, 10 AWG equipment grounding conductor with THHN insulation30. The minimum size wireway for the following with parallel conductors is: a. Two sets of three, 250 kcmil conductors with XHHW insulation b. Two, 3⁄0 AWG conductors with XHHW insulation c. 1, 4 AWG conductor with XHHW insulation d. The conductors terminate on three power distribution blocks. Each one has adimension of 4 in. wide and 3 in. high:

28. The minimum size raceway for the following conductors is: a. Three, 250 kcmil conductors with XHHW insulation b. One, 3⁄0 AWG conductor with XHHW insulation c. One, 4 AWG conductor with XHHW insulation29. The minimum size raceway for the following conductors is: a. Twelve, 6 AWG conductors with THHN insulation b. Nine, 8 AWG conductors with THHN insulation c. Eighteen, 10 AWG conductor with THHN insulation d. One, 10 AWG equipment grounding conductor with THHN insulation30. The minimum size wireway for the following with parallel conductors is: a. Two sets of three, 250 kcmil conductors with XHHW insulation b. Two, 3⁄0 AWG conductors with XHHW insulation c. 1, 4 AWG conductor with XHHW insulation d. The conductors terminate on three power distribution blocks. Each one has adimension of 4 in. wide and 3 in. high:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 13kV and that across the next unit is 12KV. Estimate: 17. i. ratio of mutual to self-capacitance ii. the bus-bar voltage of the substation. iii. Efficiency across the string of insulators
With respect to conductor insulation, describe the following location ratings: a. Dry b. Damp c. Wet
i) Calculate V1 and V2 for the voltage across the string insulator having phase voltage of 33kV for transmission line using details tabulated in the Table 3(a). Table 3(a) Type of Insulator Shunt Capacitance between each unit 0.1 C String to junction Self -Capacitance of each insulator ii) With the help of a suitable schematic diagram and necessary theoretical explanation, illustrate how to improve the efficiency of the suspension insulator.
The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C and a 60-Hz resistance of 0.0956 ohm per mile at 50C for the all-aluminum Marigold conductor, which has 61 strands and whose size is 1113 kcmil. Assuming an increase in resistance of 2 for spiraling, calculate and verify the dc resistance. Then calculate the dc resistance at 50C, and determine the percentage increase due to skin effect.
Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All strands have the same radius r.
The minimum size ratio for following branch circuit conductor is: a. Twelve, 6 AWG conductor with THHN insulation b. Nine, 8AWG Conductor with THHN insulation. c. Eighteen, 10 AWG conductor with THHN insulation d. One, 10AWG equipment grounding conductor with THHN insulation.
9. What size THWN copper conductors are required to supply a 120/208V, three-phase panelboard with 20.5KVA of noncontinuous load and 25KVA of continuous load? a. 250 kcmil b. No. 1 C. 1/0 d. 4/0
30. The minimum size wireway for the following feeder with parallel conductors is: a. Two sets of three, 250 kcmil conductors with XHHW insulation b. Two, 3/0 AWG conductor with XHHW insulation c. 1, 4 AWG conductor with XHHW insulation d. The conductors terminate on three power distribution blocks. Each one has a dimension of 4 in. wide and 3 in. high.
What is the withstand rating of a AWG copper conductor? A. 60,516 ampere squared seconds b. 121,032 ampere squared seconds c. 302,580 ampere squared seconds d. 605,160 ampere squared seconds
GMR calculate
For the overhead line of the configuration shown in Figure below operating at 60 Hz and a conductortemperature of 708C, determine the resistance per phase, inductive reactance in ohms/mile/phase,and the current carrying capacity of the overhead line. Each conductor is ACSR Cardinal of Table A.4.
Some electricians do not bother to calculate the minimum size of neutral service conductor. They size the minimum ungrounded conductor size and then use this information to determine the minimum neutral conductor size. Explain how they determine the minimum neutral size using the minimum ungrounded conductor siz