"I need the solution along with proof of the correct choice by the expert." choose the correct answer 1. The maximum break down strength of air at 76 cm mercury pressure and temperature of 25 °C is...... a. 30 V/cm b. 30 kV/cm c. 300 kV/cm d. Non of them 2. The installed capacity of a power station must be not ....... than the maximum demand. b. equal c. more a. Less 3. Area under the daily load curve divided by 24 hour gives daily d. Non of them a. average load in kW. b. maximum demand in kW. c. units generated in kwh. d. Non of them 4. In thermal power station, 5 kwh need to burn fuel has a. 860 k.calorific. b. 1500 k.calorific c. 4300 k.calorific d. Non of them. 5. Francis and Kaplan turbines are used for... heads. a. medium and high b. medium and low c. medium only. d. High only 6. For photo voltage cell, Fill factor is a. Umpimp Uscise b. Vscisc Vmpimp c. Vmpimp d. Vscisc 7. Power available from wind mill is a. PA V² b. -AV² c. PA V³ d. pA V³ 2p

"I need the solution along with proof of the correct choice by the expert." choose the correct answer 1. The maximum break down strength of air at 76 cm mercury pressure and temperature of 25 °C is...... a. 30 V/cm b. 30 kV/cm c. 300 kV/cm d. Non of them 2. The installed capacity of a power station must be not ....... than the maximum demand. b. equal c. more a. Less 3. Area under the daily load curve divided by 24 hour gives daily d. Non of them a. average load in kW. b. maximum demand in kW. c. units generated in kwh. d. Non of them 4. In thermal power station, 5 kwh need to burn fuel has a. 860 k.calorific. b. 1500 k.calorific c. 4300 k.calorific d. Non of them. 5. Francis and Kaplan turbines are used for... heads. a. medium and high b. medium and low c. medium only. d. High only 6. For photo voltage cell, Fill factor is a. Umpimp Uscise b. Vscisc Vmpimp c. Vmpimp d. Vscisc 7. Power available from wind mill is a. PA V² b. -AV² c. PA V³ d. pA V³ 2p

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Full calculation with any assumption needed. All sub questions please as it is all related.
Please answer in typing format solution
2. Explain the environmental impacts of wind power plant?
Id is : 510221
Disuss the operation of several different types of generation plants (i.e., steam, nuclear, wind, etc.)
Why Kelvin bridge is used for measurement of low resistance ____________________. a. due to a large current flow b. due to power dissipation across the circuit c. due to contact and lead resistance d. due to emf source used
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
10. In a transformer, the leakage flux of each wind- ing is proportional to the current in that winding because (a) Ohm's law applies to magnetic circuits (b) leakage paths do not saturate (c) the two windings are electrically isolated (d) mutual flux is confined to the core. 11. In a two-winding transformer, the e.m.f.per turn in secondary winding is always.........the induced e.m.f. power turn in primary. (a) equal to K times (b) equal to 1/K times (c) equal to (d) greater than. 12. In relation to a transformer, the ratio 20: 1 indi- cates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one turn on secondary.
Instantaneous voltage is multiplication of the resistace and .......... current in the resistive circuit. a) instantaneous b) average c) rms d) peak
Please solve No. 19 below. Please provide a clear and readable solution. I appreciate any help you can give me. The course subject is Electrical Machines. NOTE: The answer is given below(The answer is letter B.); show the solution. Please follow this format: Write the Given, Required, and Solution, then Box the Final answer. Thanks!!!
Q4: A power distribution station consisting of 100OKVA, 4500V/225V, and 50 cycles per second single-phase core type mutual inductance equipment is to have an approximate electromotive force per turn of 15V and operates witha maximum flux of1.4T. Based on the above scenario justify what will be the values of turns, currents, and cross-sectional area of the core? Analyze the range of load resistance of this equipment. If the load resistances are very high discuss the various methods on its heat reduction process.
Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer