Q5) a) State Ampere's circuit law.b) In a certain conducting region,H = yz(x² + y²)ax - y²xzay + 4x²y²a, A/m.(a) Determine J at (5, 2, -3)(b) Find the current passing through x = -1, 0 < y, z <2(c) Show that V⚫H=0

ANSWER : ( A )Ampere's Circuital Law:Ampere's Circuital Law states that the line integral of the…

Answered: Q5) a) State Ampere's circuit law. b)…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6- Why an insulator is represented as a capacitor C? What are the assumption modes?
Don't use ai to answer I will report you answer
For the circuit shown in Figure:a. Determine the reluctance values and show themagnetic circuit, assuming that μ = 3,000μ0.b. Determine the inductance of the device.c. The inductance of the device can be modified bycutting an air gap in the magnetic structure. If a gapof 0.1 mm is cut in the arm of length l3, what is thenew value of inductance?d. As the gap is increased in size (length), what is thelimiting value of inductance? Neglect leakage fluxand fringing effects.
1. There is another method to find the time constant RC. For a discharging capacitor its voltage can RC be expressed as V(t) = V₂e . When time t = RC, V = Voe¹ = V.(0.368). If we have a discharging curve, we follow the curve to the point where the voltage is equal to 0.368V. The time corresponding to 0.386V, is the time constant, t = RC. V V₂ 0.368 V T Use your voltage data for R₁ = 10 k2 and determine the time constant. Show your work.
The Subject is Electromagnetic II .
Boundary Conditions Two planar slabs of equal thickness but with different dielectric constants are shown inFigure. Eo in air makes an angle of 30° with the z-axis. Calculate the angle that E makes with the z-axis in each of the two dielectric layers.
10 Given a common magnetic core whose length is 100 cm, its cross-sectional area is 25 cm square. The relative permeability of the core material is 5000. Two coils are tightly wound on the core. N1 =1000 turns and N2 = 500 turns. The self-inductance of coil N1 will be: [ 7.85 m H 15.7 m H 3.927 m H 5.17 mH
symmetry argument, using words and sketches, similar to those arquments found in the lecture B# B,3 for a toroidal coil. ) Make a I,
A cylindrical solenoid 49 cm long with a radius of 7 mm has 325 tightly-wound turns of wire uniformly distributed along its length (see the figure). Around the middle of the solenoid is a two-turn rectangular loop 3 cm by 2 cm made of resistive wire having a resistance of 135 ohms. One microsecond after connecting the loose wire to the battery to form a series circuit with the battery and a 20 resistor, what is the magnitude of the current in the rectangular loop and its direction (clockwise or counter-clockwise in the diagram)? (The battery has an emf of 9 V.)
Write this out clearly
Q8 - You wish to end up with a 2um width metal line (measured at the top of the metal lead cross section). A) You are using an isotropic wet etch process on a 1um thick metal layer. What linewidth should the protective photoresist line be to get these results? Sketch the resulting structure before photoresist strip. B) now you are using a completely anisotropic etch, what is the requisite linewidth of the photoresist to achieve the same end goal? Sketch the resulting structure before the stripping of the photoresist.
4) We usually think of wires as perfect (R=0) conductors, which is not quite accurate. Real wires have resistance albeit small - usually less than an ohm. With this in mind: a. Consider a uniform cylindrical copper wire that has diameter of 1 mm and is 10 m long. What is the resistance of this wire? The resistivity of copper is 1.72 x 10-8 9-m. b. This wire is cut in half, and the two strands are used to connect an electric heater to an outlet supplying 1500 W at 120 V. Draw a simple circuit diagram, including the voltage source, resistances of the connector wires, and the calculated resistance for the heater. C. How much of the total 1500 W is absorbed by the connector wires, not by the electric heater? d. If the specific heat and density of copper are 385 J/kg°C and 8940 kg/m³ respectively, how much will the connector wires heat up after 1 minute of use? (Assume all energy absorbed by the connector wires is converted to heat and remains in the copper wire.) Remember that E cmAT,…

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Q5) a) State Ampere's circuit law. b) In a certain conducting region, H = yz(x² + y²)ax - y²xzay + 4x²y²a, A/m. (a) Determine J at (5, 2, -3) (b) Find the current passing through x = -1, 0 < y, z <2 (c) Show that V⚫H=0