For the tower shown in Figure (2), check the suitability of the proposed piled foundation with the following infiormation: (minimum safety factor against failure is (2). (neglect the group action), (V - 2250 kN, including pile cap weight) and (M 4500 kN.m), the pile group consists of one central the distributed and eight piles circumference of a (6 m) diameter circle ( 45 ) degrees appart}. pile on = 1 m 8 m diameter cap 20 m Figure (2) 10 m M 0.5 m diameter bored pile -30 kPa. y= 19 kN/m² Gs-2,7 Sand Clay

For the tower shown in Figure (2), check the suitability of the proposed piled foundation with the following infiormation: (minimum safety factor against failure is (2). (neglect the group action), (V - 2250 kN, including pile cap weight) and (M 4500 kN.m), the pile group consists of one central the distributed and eight piles circumference of a (6 m) diameter circle ( 45 ) degrees appart}. pile on = 1 m 8 m diameter cap 20 m Figure (2) 10 m M 0.5 m diameter bored pile -30 kPa. y= 19 kN/m² Gs-2,7 Sand Clay

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.8P: Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60...

See similar textbooks

Similar questions

Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table is 2 m (L1) below the top of the sand. The properties of the sand are =40, =17.5kN/m3, and sat=19kN/m3. It is proposed to excavate to a depth of 6 m (L) below the ground level. Determine the actual depth to which the sheet pile must be driven (L + D), using the net lateral pressure diagram. Note: Dactual=1.3(L3+L4)theory
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure 18.36, with a safety factor of 3. Use the a method for computing the shaft friction. FIG. 18.36
Solve Problem 12.23 using the method of Broms. Assume that the pile is flexible and free headed. Let the soil unit weight, = 16 kN/m3; the soil friction angle, = 30; and the yield stress of the pile material. FY = 21 MN/m2. 12.23 A 30 m long concrete pile is 305 mm 305 mm in cross section and is fully embedded in a sand dcposit. If nh = 9200 kN/m2, the moment at ground level Mg = 0, the allowable displacement of pile head = 12 mm; Ep = 21 106 kN/m2, and FY(pile) = 21,000 kN/m2, calculate the allowable lateral load, Qg, at the ground level. Use the elastic solution method.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load.
The tie rods from anchored sheet piles will be connected using a row of anchors, as shown in Figure 18.46a. Here H = 2.0 m, h = 1.25 m, B = 1.5 m, S = 2.5 m, = 32, and = 17.5 kN/m3. The anchor plates are made of 100 mm thick reinforced concrete with a unit weight of 24.0 kN/m3. Determine the ultimate holding capacity of the anchor used Ovesen and Stromanns method.