Please answer the following and show the step by step answer on clear paper 2. Design a rectangulan sectionand the flexural reinforcementsof the beam shown using fé=zımpa,fá=21fr = 140 mpa, and n= 10. Neglect wt. of beam60 k25ka50 kN40kN04m2m572mIn 22m

Answered: Image /qna-images/answer/dbbfcf72-721a-4672-b08f-4acbebdca457.jpg

Answered: 2. Design a rectangulan section and the…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.3P

See similar textbooks

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
The frame shown in Figure P4.7-8 is unbraced, and bending is about the x-axis of the members. All beams areW1835, and all columns areW1054. a. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. c. If Fy=50 ksi, is the stiffness reduction factor applicable to these columns?
The member shown in Figure P6.6-4 is part of a braced frame. The load and moments are computed from service loads, and bending is about the x axis (the end shears are not shown). The frame analysis was performed consistent with the effective length method, so the flexural rigidity. EI, was unreduced. Use Kx=0.9. The load and moments are 30 dead load and 70 live load. Determine whether this member satisfies the appropriate AISC interaction equation. a. Use LRFD. b. Use ASD.

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

SEE MORE TEXTBOOKS

2. Design a rectangulan section and the flexural reinforcements of the beam shown using fé=zımpa, fá=21 fr = 140 mpa, and n= 10. Neglect wt. of beam 60 k 25ka 50 kN 40kN 0 4m 2m 57 2m In 2 2m