You are replacing drinking water pipes in Asheville, NC. In one location, you must convey 10ft³/s of drinking water with a pressure head drop of 1 ft per 1000 ft of horizontal pipe. If you areusing commercial steel pipes, what is the diameter of pipe required to meet this need?

Answered: Image /qna-images/answer/7f8b4318-7ae4-4035-8d17-c3e3c03c5896.jpg

Answered: You are replacing drinking water pipes…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3 - Eagle Engineering has designed an electromagnetic pump to pump liquid sodium. The sodium moves through a pipe at A with pressure of 20 psig, then passes through the rectangular duct where it is pumped by an electromagnetic force giving it a 25-ft pump head. The liquid sodium emerges at B through a 2-inch-diameter pipe. Eagle Engineering needs to determine the value of the restraining force (F) on each arm to keep the pipe stationary. Determine this value for Eagle Engineering. For liquid sodium use a specific weight of 53.2 Ibr/ft³ B 15 ft/s
Civil
Eagle Engineering has designed an electromagnetic pump to pump liquid sodium. The sodium moves through a pipe at A with pressure of 20 psig, then passes through the rectangular duct where it is pumped by an electromagnetic force giving it a 25-ft pump head. The liquid sodium emerges at B through a 2-inch-diameter pipe. Eagle Engineering needs to determine the value of the restraining force (F) on each arm to keep the pipe stationary. Determine this value for Eagle Engineering. For liquid sodium use a specific weight of 53.2 lbf/ft3.
I need a solution within 15 minutes
Problem II. A proposed elevated tank for a certain community has a diameter of 72 inches and a height of 120 inches. It is to draw water by a pump from an aquifer down below the ground. Two steel hoops, 24.4 in? in cross section, are installed around the tank, one at the bottom and one at the top, to prevent the bursting of the tank by the water pressure inside. (Use unit weight of water, ywater = 62.4 lb/ft³) a) Compute the internal stress at the bottom of the tank (in psf). b) Determine the tensile stress at the top (in psi). c) Determine the tensile stress at the bottom (in psi).
A compound piping system consists of 1800m of 300 mm diameter, 1200 m of 400 mm diameter and 600 m of 500 mm diameter pipes of the same material (same value of f) connected in series. [ Select] What is the equivalent length in meters of a 400 mm pipe of the same material? | Select] v What is the diameter in mm of the 3.6 km equivant 1. pipeline of the same material that could replace all the three pipes?
A proposed elevated tank for a certain community has a diameter of 72 inches and a height of 120 inches. It is to draw water by a pump from an aquifer down below the ground. Two steel hoops, 24.4 in2 in cross section, are installed around the tank, one at the bottom and one at the top, to prevent the bursting of the tank by the water pressure inside. (Use unit weight of water, ywater = 62.4 lb/ft3). Note: h = 7.482ft. a) Compute the internal stress at the bottom of the tank (in psf). b) Determine the tensile stress at the top (in psi). c) Determine the tensile stress at the bottom (in psi).
A homeowner is interested in supplying water (at 20 °C) to her one-story house that is 5 m above the elevationof the water main. However, she is concerned about lack of water pressure. She hired you as an engineer todetermine if there will be sufficient pressure to supply the house at flow rate of 10 L/min through a 1.5 cmcopper pipe. The pressure at the water main is 70 psi and according to the plumbing code, flush valves require25 psi, regular water fixtures require 15 psi, and showers require 15 psi.
A brass cube 6 in on a side weighs 67 lb. We want to hold this cube in equilibrium under water by attaching a light foam buoy to it. If the foam weighs 4.5 lb/ft³, what is the minimum required volume of the buoy? QUESTION # 2 Foam Water WF Wires connecting brass and foam Brass "B 3 OF 5 Fr FBB
A barge is loaded with 200 tons of coal. The weight of the empty barge is 45 tons. If the barge is 20ft wide, 55ft long and 13 ft high, what is its draft (i.e, its depth below the water surface)? Use 1 ton = 2205lbs Unit of the Correct Answer: ft Group of answer choices 3.87 12.7 7.87 0.87
Your company will build a water tank to service a building that is 100 ft away with 20 psi water pressure at an elevation of 10 ft. What is the minimum height of the tank? Rules of thumb - Water pressure for each 1 ft = 0.433 psi Friction losses in the pipes: • 5 ft of head per 1000 ft • 2.2 psi per 1000 ft O 66.9 ft O 26.9 ft O 36.9 ft O 56.9 ft O 46.9 ft O 76.9 ft
If possible solve the two. Else solve the 1st one that is QUESTION 2

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

You are replacing drinking water pipes in Asheville, NC. In one location, you must convey 10 ft³/s of drinking water with a pressure head drop of 1 ft per 1000 ft of horizontal pipe. If you are using commercial steel pipes, what is the diameter of pipe required to meet this need?