۲/۱ العنوان use only A sanitary pipe is located at point (C) below the footings as shown in plan. Determine the increase in vertical stress on pipe due to both of tower (A) point load (p) and building (B) uniformly distributed load (q) Note: All dimensions in meters Base of both footings (tower A) and (building B) is at the same level 10.00 Building B q = 180kN/m2 6.00 10.00- 6.00 4.00 Sanitary Pipe (c) depth 3m below footings 4.00- Tower A P = 500KN oster

۲/۱ العنوان use only A sanitary pipe is located at point (C) below the footings as shown in plan. Determine the increase in vertical stress on pipe due to both of tower (A) point load (p) and building (B) uniformly distributed load (q) Note: All dimensions in meters Base of both footings (tower A) and (building B) is at the same level 10.00 Building B q = 180kN/m2 6.00 10.00- 6.00 4.00 Sanitary Pipe (c) depth 3m below footings 4.00- Tower A P = 500KN oster

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter17: Retaining Walls

Section: Chapter Questions

Problem 17.5P

See similar textbooks

Similar questions

Design a square reinforced concrete footing to support a 20-inch square tied concrete column at the edge of the building as shown below. Also check development length and force transfer in the column and at the footing. Draw the reinforcement pattern. Use a footing thickness of 24". Assume the following design conditions: -service dead load= 270 kips -service live load= 135 kips -allowable soil pressure (q)= 5000 psf -f. for the column= 5000 psi -f. for the footing= 3000 psi -fy= 60000 psi -longitudinal column steel consists of #8 bars reinf cement is uncoated -unit weight of the soil is 125 lb/ft3 -normal weight concrete Finished ground line 20" square column Y = 125 lb/ft³ 5'
2. A reinforced concrete beam having a width of 280 mm and a total depth of 600 mm isreinforced for tension at the bottom with 6 - 36 mmɸ bars placed on two layers, 4 bars onfirst layer and 2 bars on second layer. Compute the effective depth of the beam and theclear horizontal spacing between bars.
Compute its bending stresses if it is safe from wide beam shear
Determine the development length required for D25mm top tension bars in lightweight concrete. Assume fy=345MPa andfc’=20.7MPa. Use NSCP table 425.4.2.2. Stirrups are provided according to NSCP code provisions, clear spacing of bars =56mm, and clear cover = 65mm.Effective depth = 450 mm.A. 2,987.19 mm C. 1,564.72 mmB. 1,932.89 mm D. none of the above
Compute the A) analysis of loads B)total downward load and C) base area of the footing
Please use correct equations
4. If the width of the bedplate is 3m and the clearance is 0.3 what is the upper width of the machine foundation
solve for a, 5a-b=Da... 0 Outlook Do Blondes Realy.. Why C Question Completion Status: 600mm from the face of the foundation wall 600mm from the face of the foundation footing None of the above QUESTION 10 There are 4 - 15M rebar in a continuous concrete footing with a PCL measurement of 12.04 m. What is the total rebar weig 10% for laps (the mass of 15M is 1.57 kg/m)? O 21 kg 42 kg 48 kg 83 kg None of the above Cast-in-place concrete consists of built in-place of concrete structures? TRUE QUESTION 11 FALSE
pls show fbd
There are two footings resting on the ground surface. One footing is square of dimension 'B'. The other is strip footing of width 'B'. Both of them are subjected to a loading intensity of q. The pressure intensity at any depth below the base of the footing along the (A)equal in both footings. | (B) large for square footing and small for strip footing. |(C) large for strip footing and small for square footing. (D)more for strip footing at shallow depth (S B) and more for square footing at large depth (> B). centre line would be
Q1: The pad footing is used to support the axial loads 8000 lb and bending moment 2000 lb. ft. Determine the intensities W1 and W2 of the distributed loading acting on the base of footing for equilibrium. Steal Column FIKED CONNECTION 2000 b SASE PLATE -RC Footing W2 W1 40 in-
Problem 03 Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 700 kN and PLL =320 kN. Assume that the pipe is to rest on a very wide slab. Use A-36 steel and concrete f.' = 25MPA and ASD.