A two-storey school (use classroom) has interior columns that are spaced in 4.5 meters apart in two perpendicular direction. If the loading on the flat roof is estimated to be 1 kN/m^2. Determine the live load supported by a typical interior column at the ground floor level in KN. (Consider reduced live load where applicable)

A two-storey school (use classroom) has interior columns that are spaced in 4.5 meters apart in two perpendicular direction. If the loading on the flat roof is estimated to be 1 kN/m^2. Determine the live load supported by a typical interior column at the ground floor level in KN. (Consider reduced live load where applicable)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A three-storey office buiding with roof deck has an interior floor plan shown below. Each columns are spaced 6.7m each way. If the 2nd and 3rd floor levels are dedicated as business processing offices, determine the reduced live load in kPa carried by the interior column highlighted below by the ground floor. H H H H H I AT 6.7m 6.7m H 6.7m I 6.7m I
A 500mm width square tied column with reinforcement on four faces has a gross steel ratio is 0.02 and the concrete cover from the column surface to the steel centroid is 100 mm. What is the nominal axial capacity of the column if subjected to biaxial bending where ex = ey = 250 mm.? Use fc’ = 21 MPa and fy = 415 MPa, reciprocal load method, and the appropriate interaction diagram
Question: A three-story office building has interior columns that are spaced 6m apart in two perpendicular directions. If the (flat) roof loading is 0.96kPa, determine the reduced live load supported by a typical interior column located at ground level.
Calculate the ultimate axial load capacity of a round spiral column having a diameter of 450mm reinforced with six 25mm bars having fy=276 MPa. Assume fc’=34MPa.
Question 1 2.5 N/m 2.5 N/m F Using the Approximate Method for Vertical Load, produce the shear force and bending moment diagram for the frame below. The height of each storey is 5 m. 2.5 N/m 2.5 N/m в H E Using the information given and calculate what will be the axial loads on 8 m G 5m the columns. D.
Example 2.2-A simply supported reinforced beam has a cross section with a width of 500mm and a depth of 750mm, and a span of 15m. It carries a deadload of 20kN/m and an occupancy load of 4.8kN/m. It also carries a deadload of 20kN and a live load of 5kN located at 8m from the left support. The beam is made of normal density concrete. Determine the maximum factored bending moment in the beam, Mr, due to the applied factored loads.
a 410-mm diameter, non-slender, spiral column is symmetrically reinforced with 12-20 mm vertical bars. calculate the design strength (kN) of this column if subjected to axial load only. given f'c=24 Mpa and fy = 280 Mpa.
Please I need help to calculate axil force due to dead and live load in three different columns A1, A2, C3 2) Design column A2 using reinforced concrete and steel. DL= 6 LL=3.5
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)