1. A three-storey office buiding with roof deck has an interior floor plan shown below. Each columns are spaced 6.7m each way. If the 2nd and 3rd floor levels are dedicated as business processing offices, determine the reduced live load in kPa carried by the interior column highlighted below by the ground floor. I H H- H I I AT 6.7m 6.7m I 6.7m I 6.7m I

1. A three-storey office buiding with roof deck has an interior floor plan shown below. Each columns are spaced 6.7m each way. If the 2nd and 3rd floor levels are dedicated as business processing offices, determine the reduced live load in kPa carried by the interior column highlighted below by the ground floor. I H H- H I I AT 6.7m 6.7m I 6.7m I 6.7m I

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The building wall consists of 12-in. clay brick. In the interior, the wall is made from 2 x 4 wood studs, plastered on one side. If the wall is 4 ft high. Let 2x4woodstudsplasteredoneside = 12 in. claybrick = 115ps f h = 12psf Determine the load in psf of length of that the wall exerts on the floor. [Select] [Select] 548 psf 364 psf 204 psf 508 psf
The uniform distributed load (dead+live) for the building below is 120 psf. Calculate force transmitted by Gl into column C2. Draw free-body diagrams for all beams and girders involved in calculating this load. 8' 12' G2 C3 OPEN B1 B2 G1 G3 вз G4 8
Please answer it asap for an upvote. El
Calculate axil force due to dead and live load in three different columns A1, A2, C3 (shown in Fig. 1) in alllevels. Design column A2 using reinforced concrete and steel
Instruction: Use 2 decimal places in your final answers. (Theory of Structure)
Question 1 2.5 N/m 2.5 N/m F Using the Approximate Method for Vertical Load, produce the shear force and bending moment diagram for the frame below. The height of each storey is 5 m. 2.5 N/m 2.5 N/m в H E Using the information given and calculate what will be the axial loads on 8 m G 5m the columns. D.
Tributary area Determine the load support by the following with FBD
Answer asap
3.12: An RCC column is 400 mm 400 mm in section. The column is reinforced with 08 steel bars of 20 mm diameter. The column carries a load of 15 x 10 N. Find the stresses in the concrete and steel bars. Take "E" for steel and concrete as 2.1x 10 N/mm and 1.4 x 10 N/mm 400 mm 400 mm Fig. 3.26 Steel bars 8 Nos/20 mm Concrete
A 15 x 25 in. column is reinforced with four No. 9 (No. 29) bars, one in each corner as shown in Figure (a). The concrete cylinder strength is f. = 4000 psi and the steel yield strength is 60000 psi. Determine the axial load strength for zero eccentricity without subtraction of the concrete displaced by the steel, as well as with subtraction of the concrete displaced by the steel. E=0.003, E,-29000. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area 25" bar size size (soft) Ib (in) (mm) (in') (mm") 2.5" -2.5" 0.250 - % 6.35 0.05 32 0.375 = % 9.53 0.11 71 0.500 = 4 12.7 0.20 129 0.625 = % 15.9 0.31 200 0.750 = % 19.1 0.44 284 0.875 = % 222 0.60 387 1.000 = % 25.4 0.79 510 1.126 - % 28.7 1.00 645 1.270- 1% 32.3 1.27 819 No.6 0.167 0.249 3 No. 10 0.376 0.560 #4 No. 13 0.668 0.994 Pn #5 No. 16 1.043 1.552 15" No. 19 1.502 2.235 #7 No.22 2.044 3.042 #8 No 25 2 670 3.973 As No 29 3.400 5.060 A's #10 No 32 4.303 6.404 e varies #11 No.36 5.313 7.907 1.410- 35.8 1.56 1.006…
Instruction: Use 2 decimal places in your final answers. (Theory of Structure)
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)