A hinged end column 18-ft tall supports unfac- tored loads of 100 kips dead load and 60 kips live load. These loads are applied at an eccentricity of 3 in. at the bottom and 5 in. at the top. Both eccentricities are on the same side of the center- line of the column. Design a tied column with at least three bars per face using f. = 4000 psi and fy = 60,000 psi.

A hinged end column 18-ft tall supports unfac- tored loads of 100 kips dead load and 60 kips live load. These loads are applied at an eccentricity of 3 in. at the bottom and 5 in. at the top. Both eccentricities are on the same side of the center- line of the column. Design a tied column with at least three bars per face using f. = 4000 psi and fy = 60,000 psi.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Make correction to this exercice and explain in sentence or two why I made the mistake.
For problem 1, the top 2 inches of the beam is made of concrete with a compressive strenght of 8000 psi instead of 5000 psi. The rest of the beam has concrete with compressive strenght of 5000 psi.
learn Determine the reaction forces for beams B-1, B-2, and B-3. Column A Column B Girder G-1 open Girder G-2 L1 L1 L1 • Live load = 30 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 5 psf, (3) Mechanical equipment = 13 psf, (4) Suspended ceiling = 8 psf, (5) Beam = 25 Ib/ft, (6) Girder 35 lb/ft • Beam and Girder spacing: : (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Please round to the nearest one. Reaction force for Beam B-1 (one side only) = Ibs Reaction force for Beam B-2 (one side only) = Ibs Reaction force for Beam B-3 (open side) = Ibs Reaction force for Beam B-3 (Girder G-1 side) = Ibs MacBook Air II F8 F1 F2 F3 F4 F5 F6 F7 $ % & * 2 3 4 5 6 7 8 Beam B-1 Beam B-2 Beam B-3 Beam B-4 L3 L2
A concrete rectangular column with dimensions A= 420mm and B= 580 mm (See figure below) is braced against side sway. The column is to be fixed on both ends for bending about the Y-axis and to be pinned on both ends for bending about the X-axis. The unsupported length is 7.7 meters. Use f'c=35 MPa. Reinforcements are along "B" only. The column is subjected to the following service loads: Axial Dead Load =400 kN Axial Live Load=650 kN Moment about the X-axis due to Dead Load on the top of the column = 151 kN-m Moment about the Y-axis due to Dead Load on the top of the column = 138 kN-m Moment about the X-axis due to Live Load on the top of the column = 165 kN-m Moment about the Y-axis due to Live Load on the top of the column = 140 kN-m Moment about the X-axis due to Dead Load on the bottom of the column = 140 kN-m Moment about the Y-axis due to Dead Load on the bottom of the column = 131 kN-m Moment about the X-axis due to Live Load on the bottom of the column = 162 kN-m Moment…
What is the value of kip/ft of the uniform load on beam B1 ? What is the value in kips of the point load in the middle of Girder G1 ? What is the value in kips of the point load in the middle of Girder G2 ? What is the value in kips of the axial force in Column C2 on the first storey ?
Answer the helical spring problem, include complete fbd on solutions
Stress Analysis of Trusses using method of sections. pls answer within 30 mins
Answer letter b.
Answer asap
Can't figure this out
Problem 7 [RC Column Design] The short spiral column shown uses eight no. 8 bars. Assume the total loading has a low eccentricity. f.' = 3500 lbf/in², and f, = 40,000 lbf/in?. Determine the design strength. 8-No. 8 bars 22 in
I need a solution quickly, Use ACI Code