A steel pipe has an inside diameter of 196mm and an outside diameter of 206mm. It has an unsupported height of 3.5m. Using A36 steel with Fy = 248 MPa and E = 200,000 MPa. Compute the allowable axial load Pa (ASD) and ultimate axial load Pu (LRFD) that the column could carry: a. if bottom end is fixed and top end is rotation free and translation free. b. if both ends are pinned & unsupported height = 5 meters Properties of steel pipe: A = 3157.3 mm? |= 15.954 × 106 mm r= 71.09 mm

A steel pipe has an inside diameter of 196mm and an outside diameter of 206mm. It has an unsupported height of 3.5m. Using A36 steel with Fy = 248 MPa and E = 200,000 MPa. Compute the allowable axial load Pa (ASD) and ultimate axial load Pu (LRFD) that the column could carry: a. if bottom end is fixed and top end is rotation free and translation free. b. if both ends are pinned & unsupported height = 5 meters Properties of steel pipe: A = 3157.3 mm? |= 15.954 × 106 mm r= 71.09 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ber AB consists of a single C130 x 10.4 steel channel of length 2.5 m. Knowing that the pins A ross…

Q: used in a transmission not restrained in directio N/mm?.

Q: Three cylindrical rods are welded together as shown in the f igure. The diameter and modulus of…

Q: A tubular aluminum alloy [G = 4,000 ksi] shaft is being designed to transmit 370 hp at 1,100 rpm.…

Q: SP 1 The diameter in fig are 90 cm and 60 cm, at the larger end the pressure is 9.81 kpa, neglecting…

Q: Determine the effective length factor for column MN of the unbraced frame shown. The loads applied…

A: Column section MN = W12x96 Beam section = W18x46 Column length, L = 13 ft Beam length = 30 ft Dead…

Q: Q2: The reinforced concrete Isolated T-Beam shown in Figure 2, carried uniform distribution live…

A: wLL = 35 KN/mwDL = 30 KN/mfc' = 28 MPafy = 420 MPa

Q: etermine the ultimate axial capacity of the spiral column nino tho im cnira itch

Q: 1. Compute the flexural design strength (kN-m) of the column YZ. Consider the actual value of Cb.…

A: To address the problem, we'll follow these steps for each required calculation:1. Compute the…

Q: A column is constructed using a circular steel tube filled with concrete. The properties are listed…

Q: moment diagram). 2.5 lb/ft 0.617 in. 2- C 2.269 in. 6.0 ft-

Q: Determine the total load W that may be carried by the T-beam. Please step by step. Wis 35 Determine…

A: Given :

Q: Determine the design moment strength of the T-beam. Use fr=20.7 MPa and fy=414 Mpa.

A: Answer we are given f'c = 20.7 Mpa fy = 414 Mpa As = 2-25 mm As = 2 * π4*252 As = 981.75 mm2…

Q: Determine the force of member BD. Include a negative sign if the answer is in compression. Indicate…

Q: by 늘 wo B 늘 C X

A: Given Data:Length L=6.3md=300mmbf=215mmtf=14mmtw=10mmIt is required calculate the largest intensity…

Q: 3.4 Check the threshold validity below according to the bending requirement if 35MPa=m, f = 300 MPa.…

A: Dead load, DL = 5 kN/mLive Load, LL = 10 kN/mPL = 20 kNSpan, L = 4 mfc = 35 MPafy = 300 MPa3-25 mm…

Q: SOLID STEEL SHAT 5m LONG IS STRESSED АT 80 МPа WHEN TWISTED THROUGH 4°. USING G = CAN BE TRANSMITTED…

A: Shear stress, twisted angle and it has been asked to determine diameter and power. Please refer step…

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Yield Strength :Yield strength of an element is a maximum stress an element or component can bear…

Q: A concrete circular column with a radius of 350mm has f'c-25 MPa and is braced against sidesway. The…

A: Critical load The critical load is the maximum load that may be applied without causing lateral…

Q: The column shown in Figure is subjected to a service dead load of 140 kips and a service live load…

A: Given : Dead Load = 140 kips Live load = 420 kips Length of column Lcx=20 ft…

Q: g flange side. The two sides of column are . And there is a supporting point at the e of column in…

Q: A pipe assembly is subjected to a load of 200 N as shown. Determine the principle stresses,…

A: Given:- The magnitude of the load = 200 N The outside radius of the shaft = 25 mm The inner radius…

Q: The linkage below is made using two A992 steel rods, each having a circular cross section. 10klp.…

A: This question is related to Strength of Material. We calculate Diameter of Bar AB and BC using…

Q: The T-beam used in a heavy storage warehouse is made of concrete having a specific weight of 19.6…

Q: A vertical cylindrical, wooden-stave barrel is 3.5 ft in diameter and 5 ft high, and is open at the…

A: Given Dimeter of wooden stave barrel = 3.5 ft Height of wooden stave barrel = 5 ft Specific gravity…

Q: A tubular aluminum alloy [G= 4,000 ksi] shaft is being designed to transmit 410 hp at 2,700 rpm. The…

A: Given tubular shaft,

Q: Q1: Design_a simply supported rectangular reinford beam. Note: The self-weight of the beam is not…

Q: A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm…

A: Given data- A double cover butt riveted joint- Two flat plates of 200 mm width, b=200 mm, Thickness…

Q: Steel Design Two channels having the given properties shown is placed at a distance of 300 mm to…

A: Compression members are structural elements primarily subjected to axial compressive forces and…

Q: A device shown has a solid circular cross section, 35mm in diameter; it has a length of 1200 mm.and…

A: Question is based on the device made of 4150 OQT 1300 . Diameter and length of cross section are…

Q: A 500 mm x 500 mm square tied column shown is reinforced with 10 – 28 mm diameter bars with a steel…

Q: A steel column is loaded with a centric normal force. The pillar is articulated in the foot and top…

A: Safety will be assessed by EUROCODE Le = Effective length = L = 6.5 m ...(As per statement given…

Q: Quiz: Design the reinforcement steel that necessary for the shear and torsion for the rectangular…

A: Solution; Given that; Live load=10 KN/m2Dead load =5 KN/m2fck=26MPafy=400 MPa

Q: - FLUID FLOW IN PIPES I. Proving. SHOW THAT 4. hf= = fLv² 2Dg 128μLQ πρgD4

A: Given: Pipe of length L To find: Headloss in pipe

Q: Given a 9.92 m built-up column pinned at the top and fixed at the bottom with the following…

Q: A cantilever beam AB of length L = 6.5 ft supportsa trapezoidal distributed load of peak intensity…

A: Given:- L=6.5ft σallow =18 ksi τallow = 7.5 ksi To find:- the maximum permissible load q based…

Q: (2) An 8-meter-height welded-I-section column, with pinned boundary conditions at each end, is…

A: Given: L = 8 m fy = 235 N/mm2 f = 215 N/mm2

Q: Ql:-Answer the following question:- A- A concrete gate with equilateral triangular form have base…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: 1) Column AB is made of solid 410, cold worked Steel with the following specification Sy=85 KSI,…

A: For checking the type of failure, it is necessary to determine the type of column whether short or…

Q: M, Q5. The pipe is fixed to the ground at point A. It is simultaneously subjected to normal force of…

A: The given data is: Force F=10 KN Bending moment, Mx=1 KN-m Torque, T=2 KN-m Allowable stress…

Q: For the flat plate shown in the figure below (edge beam are not used), design the hatched frame…

A: According to the question we have to design the middle and column strips of the hatched slab in N-S…

Q: PROBLEM 2: The steel beam loaded below has the built-up cross section as shown. Determine the…

A: Calculate the support reactions of the given beam: RA=RB=wL2=5w

Q: Question-6b, A leaf spring is required to have a span of 2 .0 m. Determine the required thickness…

Q: Tabulate the result of your design. In 2 columns, list the tension members on the 1st column and the…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

A steel pipe has an inside diameter of 196mm and an outside diameter of 206mm. It has an
unsupported height of 3.5m. Using A36 steel with Fy = 248 MPa and E = 200,000 MPa. Compute the
allowable axial load Pa (ASD) and ultimate axial load Pu (LRFD) that the column could carry:
a. if bottom end is fixed and top end is rotation free and translation free.
b. if both ends are pinned & unsupported height = 5 meters
Properties of steel pipe:
A = 3157.3 mm?
|= 15.954 × 106 mm4
r= 71.09 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 : Data

Step 2 : a)

Step 3

Step 4

Step 5 : b)

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

DETERMINE THE THE IS MAXIMUM SAFE SERVICE LIVE LOAD THAT THE BEAM CAN CAN CARRY IF SERVICE DEAD L O A D THE BEAM WEIGHT OF THE BEAM SECTION fy = 415 MPa. TOP BARS BOTTOM BARS ARE CENTER DISTANCE 12 KM/M INCLUDING AND BASED ON THE CAPACITY SHOWN. fc : 40 MPa AND ARE 6-32 mm. AND ARE - 3 - 28 mm. CENTER TO 3 BETWEEN THE USE 2015 NSCP Is 108 mm 00 0 0 300 G ט1 108 352 70. A (1 7.2m B TOP BAR LAYERS ↓ 6.7M C OM
Qz- Find the, Critical load Pe using E=2x1ổ Pc Pery 4m
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
Determine collapse load Wu for continuous beam ABCDE loaded and supported as shown in figure . For span AC plastic moment of resistance is 50 % more than that of CE .
answer should be on the choices
A beam has a width of 200mm and a height of 250mm and is loaded as shown. Compute the maximum shear stress. Show computation and present detailed drawings/FBD’s illustrating your solution.
The steel pipe is filled with brass and subjected to a torsion T=34kNm. Determine each torsion value T, and T, taken by steel and brass. S Take the shear modulus for steel G,=80GPA and for brass G,=40GPA. T=34kNm cross-sect lon of A-B 2- steel 1- brass d,=12cm 100cm d;=4cm
Figure 1 shows the cross-section of a heavily welded I-section steel column under axial compression. The yield stress of the steel section is 300 MPa. (a) Check the slenderness of the flanges and webs. (b) Determine the effective and gross areas of the cross-section. (c) Determine the design axial capacity of the cross-section. 380 E 10 425 -8 Figure 1. Cross-section of the rectangular hollow section steel column (Units: mm)
The following tubular A36 steel shaft has an inner diameter of 25mm and an outer diameter of 35mm under the following loading condition. Determine the angle of twist of the end V. Consider: GA-36 = 75 GPa 1) What would happen if a solid shaft was used? 2) As a designer, do you recommend a solid or tubular shaft for the loading above? Why?
Q1: A simply supported reinforced conerete beam has a cross-seetion as shown in the Figure 1. Using Working Stress Method to calculate maximum load (Wmax.). (Neglect self-weight), use fe=21 MPa and 6=420 MPa Wea 40 25 2m 6m- + 300 mm Figure 1 ك إضافة ملف
For the beam below, determine the following, assume EI is constant. What is FEMAB in k-ft? -18 --96 Select the correct response: -69 2 k/ft 18 24ft
1.)Calculate the height of the neutral axis measured from the extreme compression fiber. 2.) Calculate the strength reduction factor for the given beam. 3.) Calculate the design moment for the given beam. Given b=9.25mm d=152.5mm d(prime)=32.5mm L=1.1m WsubD=6.25kn/m WsubL=8.25kn/m 4 25mm tension steel bars 4 12mm compression steelbars FsubC(prime)=28Mpa FsubY=420Mpa